C28 Flash Semaphore Register; C28 Flash Semaphore Field Descriptions - Texas Instruments Concerto F28M35 Series Technical Reference Manual

Table of Contents

Advertisement

www.ti.com
Table 1-181. MTOCIPCSTS Register Field Descriptions (continued)
Bit
Field
11
IPC12
10
IPC11
9
IPC10
8
IPC9
7
IPC8
6
IPC7
5
IPC6
4
IPC5
3
IPC4
2
IPC3
1
IPC2
0
IPC1

1.13.12.6 C28 Flash Semaphore Register

31
15
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Bit
Field
31-4
KEY
3-2
Reserved
SPRUH22I – April 2012 – Revised November 2019
Submit Documentation Feedback
Value
Description
0
MTOCIPCSTS Flag 12. M3 to C28 core IPC flag 12 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 11. M3 to C28 core IPC flag 11 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 10. M3 to C28 core IPC flag 10 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 9. M3 to C28 core IPC flag 9 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 8. M3 to C28 core IPC flag 8 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 7. M3 to C28 core IPC flag 7 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 6. M3 to C28 core IPC flag 6 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Flag 5. M3 to C28 core IPC flag 5 status. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'.
0
MTOCIPCSTS Interrupt 4. M3 to C28 IPC interrupt 4 status flag. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'
0
MTOCIPCSTS Interrupt 3. M3 to C28 IPC interrupt 3 status flag. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1'
0
MTOCIPCSTS Interrupt 2. M3 to C28 IPC interrupt 2 status flag. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1.'
0
MTOCIPCSTS Interrupt 1. M3 to C28 IPC interrupt 1 status flag. The bit is '1' if the corresponding
MTOCIPCSET bit has been written with a '1' and MTOCIPCCLR or MTOCIPCACK bit has not been
written with a '1.'
Figure 1-170. C28 Flash Semaphore Register
KEY
R=0/W
Table 1-182. C28 Flash Semaphore Field Descriptions
Value
Description
0
Writing the value 0x4CE7395 will allow writes to the SEM bits or writes are ignored. Reads will
return 0.
Note: This is to prevent spurious writes to the semaphore bits.
Reserved
Copyright © 2012–2019, Texas Instruments Incorporated
KEY
R=0/W
4
System Control Registers
3
2
1
Reserved
SEM
R-0
R/W-0
System Control and Interrupts
16
0
291

Advertisement

Table of Contents
loading

Table of Contents