ST STM32F101 series Reference Manual page 185

General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Bits 17 ADC1_ETRGINJ_REMAP: ADC 1 External trigger injected conversion remapping
Bits 16 TIM5CH4_IREMAP: TIM5 channel4 internal remap
Note: This bit is available only in high density value line devices.
Bit 15 PD01_REMAP: Port D0/Port D1 mapping on OSC_IN/OSC_OUT
Bits 14:13 CAN_REMAP[1:0]: CAN alternate function remapping
Bit 12 TIM4_REMAP: TIM4 remapping
Note: TIM4_ETR on PE0 is not re-mapped.
Bits 11:10 TIM3_REMAP[1:0]: TIM3 remapping
Note: TIM3_ETR on PE0 is not re-mapped.
Bits 9:8 TIM2_REMAP[1:0]: TIM2 remapping
185/1128
Set and cleared by software. This bit controls the trigger input connected to ADC1
External trigger injected conversion. When reset the ADC1 External trigger injected
conversion is connected to EXTI15. When set the ADC1 External Event injected conversion
is connected to TIM8 Channel4.
Set and cleared by software. This bit controls the TIM5_CH4 internal mapping. When reset
the timer TIM5_CH4 is connected to PA3. When set the LSI internal clock is connected to
TIM5_CH4 input for calibration purpose.
This bit is set and cleared by software. It controls the mapping of PD0 and PD1 GPIO
functionality. When the HSE oscillator is not used (application running on internal 8 MHz RC)
PD0 and PD1 can be mapped on OSC_IN and OSC_OUT. This is available only on 36-, 48-
and 64-pin packages (PD0 and PD1 are available on 100-pin and 144-pin packages, no
need for remapping).
0: No remapping of PD0 and PD1
1: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT,
These bits are set and cleared by software. They control the mapping of alternate functions
CAN_RX and CAN_TX in devices with a single CAN interface.
00: CAN_RX mapped to PA11, CAN_TX mapped to PA12
01: Not used
10: CAN_RX mapped to PB8, CAN_TX mapped to PB9 (not available on 36-pin package)
11: CAN_RX mapped to PD0, CAN_TX mapped to PD1
This bit is set and cleared by software. It controls the mapping of TIM4 channels 1 to 4 onto
the GPIO ports.
0: No remap (TIM4_CH1/PB6, TIM4_CH2/PB7, TIM4_CH3/PB8, TIM4_CH4/PB9)
1: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15)
These bits are set and cleared by software. They control the mapping of TIM3 channels 1 to
4 on the GPIO ports.
00: No remap (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1)
01: Not used
10: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1)
11: Full remap (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9)
These bits are set and cleared by software. They control the mapping of TIM2 channels 1 to
4 and external trigger (ETR) on the GPIO ports.
00: No remap (CH1/ETR/PA0, CH2/PA1, CH3/PA2, CH4/PA3)
01: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2, CH4/PA3)
10: Partial remap (CH1/ETR/PA0, CH2/PA1, CH3/PB10, CH4/PB11)
11: Full remap (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11)
DocID13902 Rev 15
RM0008