Scanlab RTC6 PCIe Board Installation And Operation Manual page 307

Status Monitoring and Diagnostics
(n_) get_head_status ..................................... 406
(n_) get_overrun ............................................ 419
(n_) get_value ................................................ 443
(n_) get_values ............................................... 445
(n_) get_waveform ........................................ 447
(n_) get_waveform_offset ............................. 448
(n_) measurement_status ............................. 546
(n_) stop_trigger ............................................ 799
iDRIVE Commands
(n_) control_command .................................. 346
(n_) get_transform ........................................ 437
(n_) get_transform_offset ............................. 438
(n_) read_user_data ....................................... 589
(n_) send_user_data ...................................... 610
transform ................................................ 831
(n_) upload_transform .................................. 835
Pixel Output Mode
(n_) set_default_pixel .................................... 623
I/O Commands
(n_) get_free_variable ................................... 402
(n_) get_io_status .......................................... 410
(n_) get_mcbsp .............................................. 418
(n_) mcbsp_init .............................................. 544
(n_) mcbsp_init_spi ........................................ 545
(n_) periodic_toggle ...................................... 572
(n_) read_analog_in ...................................... 579
(n_) read_io_port ........................................... 582
(n_) read_io_port_buffer ............................... 583
(n_) read_mcbsp ............................................ 585
(n_) read_multi_mcbsp .................................. 586
(n_) rs232_config ........................................... 594
(n_) rs232_read_data ..................................... 595
(n_) rs232_write_data ................................... 596
(n_) rs232_write_text .................................... 596
(n_) set_free_variable .................................... 658
(n_) set_laser_off_default ............................. 672
(n_) set_mcbsp_freq ...................................... 685
(n_) set_mcbsp_out_ptr ................................ 697
(n_) set_port_default ..................................... 716
(n_) uart_config ............................................. 834
(n_) write_8bit_port ...................................... 851
(n_) write_da_1 .............................................. 854
(n_) write_da_2 .............................................. 855
(n_) write_da_x .............................................. 856
(n_) write_io_port .......................................... 860
(n_) write_io_port_mask ............................... 861
RTC6 boards
Doc. Rev. 1.0.21 en-US
10 RTC6 Commands
Starting and Stopping Lists by External
Control Signals and Master/Slave
Synchronization
(n_) get_counts .............................................. 396
(n_) get_master_slave .................................... 417
(n_) get_startstop_info .................................. 426
(n_) set_control_mode .................................. 620
(n_) set_extstartpos ....................................... 637
(n_) set_max_counts ...................................... 685
(n_) simulate_ext_start_ctrl ........................... 783
(n_) sync_slaves ............................................. 807
List Handling and List Status
(n_) auto_change ........................................... 335
(n_) auto_change_pos ................................... 336
(n_) get_lap_time ........................................... 411
(n_) get_status ............................................... 428
(n_) get_wait_status ...................................... 446
(n_) pause_list ................................................ 571
(n_) quit_loop ................................................ 574
(n_) read_status ............................................. 587
(n_) release_wait ............................................ 592
(n_) restart_list ............................................... 594
(n_) set_pause_list_cond ............................... 709
(n_) set_pause_list_not_cond ........................ 710
(n_) start_loop ............................................... 786
(n_) stop_execution ....................................... 798
(n_) stop_list .................................................. 798
Input Pointer Commands
(n_) get_input_pointer .................................. 410
(n_) get_list_pointer ...................................... 413
(n_) load_list .................................................. 505
(n_) set_input_pointer ................................... 660
(n_) set_start_list ........................................... 746
(n_) set_start_list_1 ....................................... 746
(n_) set_start_list_2 ....................................... 746
(n_) set_start_list_pos .................................... 747
Output Pointer Commands
(n_) execute_at_pointer ................................ 384
(n_) execute_list ............................................. 385
(n_) execute_list_1 ......................................... 385
(n_) execute_list_2 ......................................... 385
(n_) execute_list_pos ..................................... 386
(n_) get_out_pointer ..................................... 418
307