Siemens SINAMICS G List Manual page 366

Parameters
Parameters for data sets
p1416[0...n]
p1428[0...n]
p1429[0...n]
p1433[0...n]
p1434[0...n]
p1435[0...n]
p1441[0...n]
p1442[0...n]
p1452[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
p1460[0...n]
p1461[0...n]
p1462[0...n]
p1463[0...n]
p1464[0...n]
p1465[0...n]
p1470[0...n]
p1472[0...n]
p1488[0...n]
p1489[0...n]
p1496[0...n]
p1499[0...n]
p1514[0...n]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
p1530[0...n]
p1531[0...n]
p1570[0...n]
p1574[0...n]
p1580[0...n]
p1582[0...n]
p1584[0...n]
p1594[0...n]
p1596[0...n]
p1610[0...n]
p1611[0...n]
p1616[0...n]
p1654[0...n]
p1656[0...n]
p1657[0...n]
p1658[0...n]
p1659[0...n]
p1660[0...n]
p1661[0...n]
p1662[0...n]
p1663[0...n]
p1664[0...n]
p1665[0...n]
1-366
Speed setpoint filter 1 time constant / n_set_filt 1 T
Speed pre-control balancing deadtime / n_pre bal t_dead
Speed pre-control balancing time constant / n_prectrl bal T
Speed controller reference model natural frequency / n_ctrl RefMod fn
Speed controller reference model damping / n_ctrl RefMod D
Speed controller reference model deadtime / n_ctrRefMod t_dead
Actual speed smoothing time / n_act T_smooth
Actual speed smoothing time / n_act T_smooth
Speed actual value smoothing time (SLVC) / n_act T_smoothSLVC
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow.
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up.
Adaptation factor, lower / Adapt_factor lower
Adaptation factor, upper / Adapt_factor upper
Speed controller P gain adaptation speed, lower / n_ctrl Kp n lower
Speed controller P gain adaptation speed, upper / n_ctrl Kp n upper
Speed controller integral action time adaptation speed, lower / n_ctrl Tn n lower
Speed controller integral action time adaptation speed, upper / n_ctrl Tn n upper
Speed controller adaptation speed, lower / n_ctrl n lower
Speed controller adaptation speed, upper / n_ctrl n upper
Speed controller sensorless operation P-gain / n_ctrl SLVC Kp
Speed controller sensorless operation integral action time / n_ctrl SLVC Tn
Droop input source / Droop input,source
Droop feedback scaling / Droop scaling
Acceleration pre-control scaling / a_before scaling
Accelerating for torque control, scaling / a for M_ctrl scal
Supplementary torque 2 scaling / M_suppl 2 scal
CO: Torque limit, upper/motoring / M_max upper/mot
CO: Torque limit, lower/regenerative / M_max lower/regen
CO: Torque limit, upper/motoring, scaling / M_max up/mot scal
CO: Torque limit, lower/regenerating scaling / M_max low/gen scal
Power limit, motoring / P_max mot
Power limit, regenerating / P_max gen
CO: Flux setpoint / Flux setpoint
Voltage reserve dynamic / U_reserve dyn
Efficiency optimization / Efficiency opt.
Flux setpoint smoothing time / Flux setp T_smth
Flux setpoint smoothing time for field-weakening operation / Flx setp T_smth Fs
Field-weakening controller, P gain / Field_ctrl Kp
Field weakening controller integral-action time / Field_ctrl Tn
Torque setpoint static (SLVC) / M_set static
Supplementary accelerating torque (SLVC) / M_suppl_accel
Current setpoint smoothing time / I_set T_smooth
Current setpoint torque-generating smoothing time / Isq_set T_smooth
Activates current setpoint filter / I_set_filt active
Current setpoint filter 1 type / I_set_filt 1 Typ
Current setpoint filter 1 denominator natural frequency / I_set_filt 1 fn_n
Current setpoint filter 1 denominator damping / I_set_filt 1 D_n
Current setpoint filter 1 numerator natural frequency / I_set_filt 1 fn_z
Current setpoint filter 1 numerator damping / I_set_filt 1 D_z
Current setpoint filter 2 type / I_set_filt 2 Typ
Current setpoint filter 2 denominator natural frequency / I_set_filt 2 fn_n
Current setpoint filter 2 denominator damping / I_set_filt 2 D_n
Current setpoint filter 2 numerator natural frequency / I_set_filt 2 fn_z
 Siemens AG 2004 All Rights Reserved
SINAMICS G List Manual, Edition 12.2004