Siemens SINAMICS G List Manual page 139

Dependency: Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets a value for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1022, p1023, r1197
Note: If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
p1022[0...n] BI: Fixed speed setpoint selection Bit 2 / n_set_fixed Bit 2
VECTOR Can be changed: T
Data type: Unsigned32
P-Group: Setpoints
Min
-
Description: Sets the signal source to select the speed/velocity fixed setpoint.
Dependency: Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets a value for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1021, p1023, r1197
Note: If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
p1023[0...n] BI: Fixed speed setpoint selection Bit 3 / n_set_fixed Bit 3
VECTOR Can be changed: T
Data type: Unsigned32
P-Group: Setpoints
Min
-
Description: Sets the signal source to select the speed/velocity fixed setpoint.
Dependency: Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets a value for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1021, p1022, r1197
Note: If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
r1024 CO: Fixed speed setpoint effective / n_set_fixed eff
VECTOR Can be changed: -
Data type: Floating Point
P-Group: Setpoints
Min
- [1/min]
Description: Displays the selected and effective fixed speed/velocity setpoint.
This setpoint is the output value for the fixed speed/velocity setpoints and must be appropriately interconnected
(e.g. with the main setpoint).
Recommenda- Interconnect the signal with main setpoint (p1070).
tion:
Dependency: Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets a value for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1070, r1197
Note: If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
 Siemens AG 2004 All Rights Reserved
SINAMICS G List Manual, Edition 12.2004
Data set: CDS
Units group: -
Max
-
Data set: CDS
Units group: -
Max
-
Data set: -
Units group: SPEED_ROT
Max
- [1/min]
Parameters
Parameter list
Access level: 3
Function diagram: 2505
Unit selection: -
Factory setting
0
Access level: 3
Function diagram: 2505
Unit selection: -
Factory setting
0
Access level: 3
Function diagram: 1550,
3010
Unit selection: -
Factory setting
- [1/min]
1-139