Page 3
Preface This manual describes how to use the Command Line Interface (CLI) to configure and manage the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system, the FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system, or the FUJITSU Storage ETERNUS DX200 All Flash Array (hereinafter referred to as ETERNUS DX).
Page 4
• FUJITSU Storage ETERNUS DX200F All Flash Array Operation Guide (Basic) • FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETER- NUS DX200F All Flash Array Message List • FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage system Configuration Guide (NAS) •...
Page 5
Preface • ETERNUS Web GUI User's Guide (Operation) FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array • ETERNUS Web GUI User's Guide (Settings) FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array •...
Note that some cases, two or more parameters can be specified by separating them with a comma. • Italics are used to show variables such as values and characters that appear in command parameters and output examples. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 7
The following naming conventions are used in this manual for the ETERNUS DX models. ETERNUS DX models Naming conventions ETERNUS DX100 S3/DX200 S3 Disk storage system ETERNUS DX ETERNUS DX500 S3/DX600 S3 Disk storage system ETERNUS DX200F All Flash Array...
Page 18
File System Maintenance ....................805 show nas-df ............................806 show nas-fsstat ............................808 show nas-fsmntstat ..........................810 7.10 NAS Function Restoration ....................811 forced nas-fsmount ..........................812 forced nas-fsunmount ..........................813 forced nas-fsoffline ..........................814 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 19
Specifying a Port Group and Performing LUN Mapping................927 D.2.3 Specifying a Port and Setting LUN Mapping ....................927 Setting Cancellation......................928 D.3.1 Canceling Mapping............................929 D.3.2 Deleting LUN Groups ........................... 929 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 20
Component Status ......................932 Drive Status ........................933 Volume Status........................933 Pool Status (TPP/FTRP/FTSP Status).................. 934 RAID Group Status......................934 Key Status ........................935 Key Server Status ......................936 Appendix F Default Value List ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The default IP address is assigned to the following ports. • With the ETERNUS DX100 S3/DX200 S3 or the ETERNUS DX200F RMT port • With the ETERNUS DX500 S3/DX600 S3 FST port The network for the MNT port must be configured from the "set network" command.
For the ETERNUS DX600 S3, from 0 to a, from 10 to 1a, from 20 to 2a, and from 30 to 3a can be spec- ified. There are no drive enclosures in the ETERNUS DX200F. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The format that can be used for drive numbers is either "xxyy" or "xyy". "xx" or "x" indicates the enclosure number. For the ETERNUS DX100 S3/DX200 S3 or the ETERNUS DX200F, 00 or 0 indicates the controller enclosure. For details, refer to "1.2.3 Drive Enclosure Syntax"...
Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
A hyphenated range of RAID group numbers from to z: 2-5 A list of RAID group numbers, RAID group ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
A hyphenated range of host response numbers from to z: 2-5 A list of host response numbers, host response ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
(CA) number, and "z" indicates the host interface port number. For example, "110" indicates CM#1-CA#1-Port#0. Two or more parameters can be specified by separating them with a comma (,). To indicate both CM#0-CA#0-Port#0 and CM#1-CA#1-Port#0, specify "-port 000,110". ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
An host group name and an host group number cannot both be specified in the same command. Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The history contains all the commands entered in the active CLI session. A command from the history can be recalled, edited, and run. For details about usable keys, refer to "1.5 Command Editing Hotkeys" (page 32). ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Convert the rest of a word to uppercase Esc-C or Esc-c Convert the rest of a word to lowercase Esc-L or Esc-l Enter command and redisplay prompt Ctrl-Z or Ctrl-z Refresh input line Ctrl-L or Ctrl-l ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
# Note that one or more spaces are required before a question mark. CLI> show host-response ? [-host-response-num - Host response numbers to display details [-host-response-nam - Host response names to display details ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
GUI session or another CLI session that uses the locked resource completes, and then execute the command again. Resources can be forcibly released by using the "set clienv-force-unlock" command. This is useful when a terminal is suddenly disconnected or unexpected errors occur. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Even though designation of an Ethernet port by using CLI is not required, doing so allows the operator to specify which network the FTP server belongs to. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The command syntax • Parameters A description of parameter(s) • Output (only for reference commands) A description of information displayed by the command • Example(s) One or more examples of the command ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
-type de -de enclosure_number Details of specific disks show disks -disks disks Details of all disks show disks -disks all Product IDs of all disks' show disks -disks productid Hardware information show hardware-information ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Hot expansion and recovery of the controller is required. ■ Example(s) The following example displays a summary of the system status: CLI> show status Summary Status [Normal] CLI> show status Summary Status [Error] CLI> show status Summary Status [Warning] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Serial number of the system Device Identification Number Device identification number used by the ETERNUS Multipath Driver or other external software to identify the storage system. Status Status of the system ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 40
Controller Module’s PCIe Flash Module status and the status code (only for the ETERNUS DX500 S3/DX600 S3). The "#n" in the field indicates the controller module number and the "#m" in the field indicates the PCIe Flash Module number. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 41
Supply Unit number. Example: PSU#1 [Status / Status Code] (For Power Supply Unit#1) DISK#xyy Disk status (only for the ETERNUS DX100 S3/DX200 S3 and the ETERNUS DX200F) Example: CE-Disk#1 [ status ] (Disk #001 status) (For details, refer to "1.2.4 Drive Syntax" (page 23).)
Page 42
System Message No. Message 1 P 100000XX-XXXXX 2 P 500000XX-XXXXX The following example shows the information that is displayed when the controller enclosure is specified for the ETERNUS DX100 S3/DX200 S3: CLI> show enclosure-status -type ce Controller Enclosure Information Location Status...
CM Active EC EC number of the active firmware (The current operating firmware) CM Next EC EC number of the stand-by firmware (The generation number of the firmware after the next power cycle) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 47
CM FAN CM FAN status and the status code (ETERNUS DX500 S3/DX600 S3 only) CA# Parts Number CA parts number CA# Serial Number CA serial number CA# Hard Revision CA hardware revision ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 48
BUD controller firmware version (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SCU (System Capacitor Unit) status and the status code (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SCUs are electric double layer capacitors embedded in a controller module. SCUs provide the power to move the cache data to the SATA SSD flash memory if there is a power outage.
Page 49
Link Status Link status (Link Up, Link Down, or if requesting auto negotiation, then the actual transfer rate is displayed.) Port WWN Port World-Wide-Name Node WWN Node World-Wide-Name iSCSI Name iSCSI Name iSCSI Alias Name iSCSI Alias Name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 50
The time required for processes stopped due to disconnection to restart from where they were stopped after reconnection Reconnection Wait Time The time required to reconnect the TCP connection Fabric Name Fabric Name SFP Type SFP Type ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 51
Temperature (Present, Warning(Low/High), and Alarm(Low/High)) Voltage Voltage (Present, Warning(Low/High), and Alarm(Low/High)) Current Current (Present, Warning(Low/High), and Alarm(Low/High)) TX Power Transmitter power (Present, Warning(Low/High), and Alarm(Low/High)) RX Power Receiver power (Present, Warning(Low/High), and Alarm(Low/High)) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 52
BCU serial number BCU# Hard Revision BCU hardware revision The following table shows the output information of the power supply units. Status/Status Code Power supply unit (PSU#n) status and the status code ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 53
2.1 Storage System Status > show fru-ce ■ Example(s) The following example displays the status and details of controller module #0 for FC (For ETERNUS DX100 S3/ DX200 S3, ETERNUS DX500 S3/DX600 S3): CLI> show fru-ce -type cm0 CM#0 Information...
Page 54
Host Response SFP Type [ShortWave] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 55
CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [Auto Negotiation] Link Status PHY#0[Link Down PHY#1[Link Down PHY#2[Link Down PHY#3[Link Down Port WWN [500000E0D1000011] Node WWN [500000E0D1000000] Host Affinity [Disable] Host Response ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 56
Reconnection Wait Time SFP Type [SFP+] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 57
[0-00] SCU#0 Parts Number SCU#0 Serial Number SCU#0 Hard Revision SCU#1 Status/Status Code [Normal / 0xE001] SCU#1 Voltage [9.40V] SCU#1 Expires [0-00] SCU#1 Parts Number SCU#1 Serial Number SCU#1 Hard Revision ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 58
Chapter 2 Status Display 2.1 Storage System Status > show fru-ce The following example displays the status of PSU#0: CLI> show fru-ce -type psu0 CE PSU#0 Information Status/Status Code [Normal / 0xE001] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Error code to identify error events that have occurred in an expander. This information is only displayed when the Status is not "Normal" or "Undefined". World Wide Name (For FEM#1, a hyphen (-) is shown.) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 60
FEM (FEM#n) status and the status code Error Code Error code to identify error events that occurred in a Fan Expander Module. This information is only displayed when the Status is not "Normal" or "Undefined". ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 61
Power supply unit (PSU#n) status and the status code Error Code Error code to identify error events that occurred in a power supply unit. This information is only displayed when the Status is not "Normal" or "Undefined". ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 62
[EC#2] Firmware Version [V10L10-0000] The following example displays the status of PSU#0 in drive enclosure #2: CLI> show fru-de -de 2 -type psu0 DE#2 PSU#0 Information Status/Status Code [Normal / 0xE001] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
All the undefined disks All disks in the controller enclosure (only for the ETERNUS DX100 S3/DX200 S3 and the ETERNUS DX200F) All disks in the specified drive enclosure When using this parameter, the "-de" parameter and the drive enclosure number must also be specified.
Page 64
Serial Number Serial number World Wide Name Firmware Revision Disk firmware version Total completed passes Total number of disk patrols Progress with current pass Progress rate of the current disk patrol ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 65
------------- ----------------------------- ------- --------------- ---------- ------------------- --------- DE#4-Disk#0 Available 3.5 Online 7200 Data DE#4-Disk#1 Available 3.5 Online 7200 Data DE#5-Disk#1 Available 3.5 Online 7200 Data DE#6-Disk#11 Available(Predictive Failure) 4TB 3.5 Online 7200 Data ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 66
Progress with current pass [79%] Completed passes since last Power On [30737Cycle] The following example displays the product ID list: CLI> show disks -disks productid Product ID Revision ---------------- -------- ST373455SS 12CD ST99999999 3456 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Serial number embedded in the enclosure Other Information Individual identifier embedded in the controlling Fujitsu enclosure. For each component, the following items are displayed. For single controller models, both controller module #1 and expander module #1 are indicated by hyphens. Information is not displayed for drive enclosures that do not exist.
The functions to control RAID groups are as follows: • Creating a RAID group • Deleting RAID groups • Changing an existing RAID group • LDE, Logical Device Expanding (expanding a RAID group) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Free Capacity (MB) Free capacity (Unit: MB) Stripe Depth (Unit: KB) Stripe Depth (Unit: KB) (Only when viewing details) Key Group Usage status of the key group (Only when viewing details) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 71
<Disk List> Disk Status Usage Mirroring -------------- ----------------------------- ------------------- -------------- CE-Disk#2 Broken Data CE-Disk#3 Available Data CE-Disk#5 CE-Disk#4 Available Data CE-Disk#7 CE-Disk#5 Available Data CE-Disk#3 CE-Disk#7 Available Global Hot Spare CE-Disk#4 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 72
Data DE#01-Disk#1 Available Data DE#01-Disk#2 Available Data DE#01-Disk#3 Available Data DE#01-Disk#4 Available Data DE#01-Disk#5 Broken Data DE#01-Disk#6 Available Data DE#01-Disk#7 Available Data DE#01-Disk#8 Available Data DE#01-Disk#9 Available Data DE#01-Disk#10 Available Data ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The remaining time is less than 1 day but 1 hour or more. The remaining time is less than 1 hour but 1 minute or more. Less than 1min The remaining time is less than 1 minute. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 74
RAID Group Status Rebuild/Copyback Expanding No. Name Progress Estimated time left Remaining size Progress --- ---------------- ------------------------------- -------- ------------------- -------------- --------- 0 RAIDGROUP001 Copyback 87% 12h 59min 1024MB 1 RAIDGROUP012 Available ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
If "auto" is specified, the fixed controller, which is calculated automatically by the system, is assigned. If this parameter is omitted, the "auto" mode is set. Controller module#0 Controller module#1 auto Automatically (default) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 76
RAID6(3+2)×6, HS×1 ■ Example(s) The following example creates a RAID group named "RGP001". RAID1 level is assigned using disks #003 and #004: CLI> create raid-group -name RGP001 -level 1 -disks 003,004 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The key group is used (the SED authentication key that is managed by the key server is used). disable The key group is not used (the common key in the ETERNUS DX is used). ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 78
The following example changes the CM number that is associated with RAID groups #2 and #4. The new CM number is "CM#1": CLI> set raid-group -rg-number 2,4 -assigned-cm 1 The following example sets a key group for RAID groups #2 and #4: CLI> set raid-group -rg-number 2,4 -key-group enable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
■ Example(s) The following example deletes the RAID group named "R1": CLI> delete raid-group -rg-name R1 The following example deletes consecutive RAID groups #1 - #8: CLI> delete raid-group -rg-number 1-8 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Optional. This parameter specifies the new RAID group name to be used for the expanded RAID group. For details, refer to "1.2.5 Alias Name Syntax" (page 23). names RAID group name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 81
3.1 RAID Group Management > expand raid-group ■ Example(s) The following example expands the RAID group named "RGP001" using six disks, and changes the RAID level to RAID5: CLI> expand raid-group -rg-name RGP001 -disks 101-103,201-203 -level 5 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Hot spares must be of the same disk type and must have the same (or larger) capacity as the disks in the assigned RAID group. A list of registered hot spare disks can be displayed by using the "show disks" command. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Global Hot Spare pool. Adding additional Global Hot Spares does not remove any hot spares that are previously set: CLI> set global-spare -disks 101,102 CLI> set global-spare -disks 103 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example releases disk #011 from the Global Hot Spares: CLI> release global-spare -disks 011 The following example releases disks #101 to #105 from the Global Hot Spares: CLI> release global-spare -disks 101-105 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Dedicated Hot Spare to the RAID group named "RGP1". Disk #111 is assigned as a Dedicated Hot Spare to the RAID group named "RGP2": CLI> set dedicated-spare -disks 110,111 -rg-name RGP1,RGP2 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 86
Dedicated Hot Spare to the same RAID group. Adding additional Dedicated Hot Spares does not remove any hot spares that are previously set: CLI> set dedicated-spare -disks 101 -rg-name RGP1 CLI> set dedicated-spare -disks 102 -rg-name RGP1 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Drive ■ Example(s) The following example releases Dedicated Hot Spare #110: CLI> release dedicated-spare -disks 110 The following example releases Dedicated Hot Spares #110 and #111: CLI> release dedicated-spare -disks 110,111 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The commands described in this section are not supported in the ETERNUS DX200F. The three steps involved in enabling the Eco-mode functions are as follows: Procedure Enable the Eco-mode. Create an Eco-mode schedule. Assign the Eco-mode schedule to RAID groups. End of procedure ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Number of times that a disk motor will power off and on in one day ■ Example(s) The following example displays the current Eco-mode settings: CLI> show eco-mode Mode [Enable] Host I/O Monitoring Time [60 min.] Disk Motor Control Limit Count [5] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Eco-mode is enabled. disable Eco-mode is disabled. ■ Example(s) The following example enables the Eco-mode. CLI> set eco-mode -mode enable The following example disables the Eco-mode: CLI> set eco-mode -mode disable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Eco-mode schedule event identifiers Eco-mode schedule event number Type Eco-mode schedule event type Details Explanation for the Eco-mode schedule event type Time Starting time and ending time of the Eco-mode schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 92
3 SC003_TEMP Event No. Type Details Time --- ------------- ----------------------------------------- ----------------------- 1 Specific-day 6days from December 13 from [06:00] to [18:00] 2 Specific-week December 1st week Monday-Friday from [06:00] to [18:00] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
(END) are separated by a comma (,). The day of the week must be specified in the following format. The end day of the week must be after the start day of the week. The first day starts from Monday. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 94
(From the 3rd Monday to the 3rd Wednesday in May) Example: -event-type specific-week,05,3rd,wed,mon (From the 3rd Wednesday to the 3rd Monday in May) (When May 1st is a Monday) Monday Tuesday Wednesday Thursday Friday Saturday Sunday ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 95
The following example creates an Eco-mode schedule. The Eco-mode schedule name is "SC001". The Eco- mode schedule will apply every day from 06:00 to 18:00: CLI> create eco-schedule -name SC001 -event-type every-day -event-from 0600 -event-to 1800 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
-event-type Optional. This parameter specifies the Eco-mode schedule event type. If omitted, the existing setting is not changed. every-day The Eco-mode schedule is applied to every day. A suboperand is not required. Example: -event-type every-day ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 97
(from the 3rd Monday to the 3rd Wednesday in May is OK) Example: Incorrect -> -event-type specific-week,05,3rd,wed,mon (from the 3rd Wednesday to the 3rd Monday in May is not OK) (When May 1st is a Monday) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 98
CLI> set eco-schedule -schedule-name SC001 -event-number 2 -event-type every-day -event-from 0600 -event-to 1800 The following example changes the Eco-mode schedule name. The new Eco-mode schedule name is "SC002_NEW": CLI> set eco-schedule -schedule-name SC001 -name SC002_NEW ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example will delete Eco-mode schedule event #2 in the Eco-mode schedule named "SC001": CLI> delete eco-schedule -schedule-name SC001 -event-number 2 The following example will delete both the Eco-mode schedules named "SC002" and "SC003" at the same time: CLI> delete eco-schedule -schedule-name SC002,SC003 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Eco-mode schedule name (In the case of a schedule by a cooperative software, "External" is displayed.) Motor Status Current status of the disk motors Control Status Control status by a control command ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 101
60000 Drive motor off 1 SC001 Active [OFF] 30 RGP030 RAID5 Available CM#1 89654 Drive always on 128 External Active [OFF] 31 RGP031 RAID0 Present CM#1 22301 Drive always on 2 SC002 Active [OFF] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
If omitted, the existing setting is not changed. For details, refer to "1.2.14 Eco-mode Schedule Syntax" (page 29). To set software linkage, specify "128" for "-schedule-number". In this case, "External" is automatically set as the schedule name. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 103
Eco-mode schedule #2 with the same RAID group. These executions result in Eco- mode schedule #1 being released: CLI> set eco-raid-group -rg-name RGP001 -schedule-number 1 -action enable CLI> set eco-raid-group -rg-name RGP001 -schedule-number 2 -action enable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example releases an Eco-mode schedule associated with the RAID group named "RGP001": CLI> release eco-raid-group -rg-name RGP001 The following example releases an Eco-mode schedule associated with RAID groups #1 – #10 at the same time: CLI> release eco-raid-group -rg-number 1-10 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
• Only one parameter can be specified. • Other parameters (except for "-mode default") cannot be specified at the same time. pool_number Thin Provisioning Pool number pool_name Thin Provisioning Pool name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 107
A Snap Data Pool Volume (SDPV) for Advanced Copy functions A Thin Provisioning Volume (TPV) (including a Thin Provisioning Volume for a NAS) A Flexible Tier Volume (FTV) A Wide Striping Volume (WSV) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 108
Volume status Type Volume type and volume usage (This information appears when the NAS function is enabled.) Usage Details Detailed volume usage (This information appears when the NAS function is enabled.) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 109
WSVs use in each RAID group, specify the "-mode expansion" parameter or the "-mode wsv" parameter. This information is not displayed for volume types that are not Open volumes, SDVs, SDPVs, or WSVs. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 110
— — — — — — — — -mode ftv D — — — — — — — D — — — — — D D D — D D — — ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 111
CLI> show volumes -type sdpv Volume Status RG or TPP or FTRP Size(MB) Copy Reserved Name No. Name Protection Deletion ----- ------------------------------- ------------------------- --- ---------------- --------- ---------- -------- 10 SDPV Available 0 RLU#0 102400 Disable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Status Volume status Formatting Information on the formatting progress Progress Progress A value from 0% to 99% or "-" is displayed. ("-" indicates that formatting is not performed or is complete) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 115
Migrating Encrypting Balancing Zero Reclamation Name Progress Estimated time left Remaining size Progress Progress Progress Progress 1 VOL001 Available 80% 30days or more 134217728MB 12 VOL012 Rebuild 80% 01day 23h 59min 128MB ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 116
Progress Estimated time left Remaining size Progress Progress Progress Progress 1 VOL001 Available 80% 01h 00min 128MB 2 VOL002 Available 3 TPV003 Rebuild 4 VOL004 Rebuild 90% 01min Less than 1MB 10 VOL010 Available 80% calculating ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
A list of all of the volumes is displayed. ■ Output Volume Volume identifiers Volume number Name Volume name Type Volume type Volume UID (Universally Unique Identifier) LUN Group LUN group identifiers LUN group number Name LUN group name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
23). This parameter can be specified when the "-type tpv" parameter, the "-type nas-tpv" parameter, or the "-type nas-tpv-backup" parameter is specified. pool_number Thin Provisioning Pool number pool_name Thin Provisioning Pool name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 120
Status) of the NAS system volume format. A completion status is displayed if the NAS vol- ume is created normally. Check the status of the NAS engine using the "show fru-ce" command. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 121
If a NAS volume (the "nas-tpv" option or the "nas-tpv-backup" option) is selected, the volume capacity can be specified within the ranges shown below (not supported in the ETERNUS DX200F). ETERNUS DX100 S3/DX200 S3 From 400GB to 65,519GB ETERNUS DX500 S3/DX600 S3...
Page 122
The Wide Stripe Size for the Wide Striping Volume is set to 2MB. Note that if the Stripe Size of the RAID group exceeds 2MB, the actual Stripe Size of the RAID group is used for the WSV that is to be created. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 123
The EXC function is not available for a created volume when this volume belongs to a RAID group or a pool that consists of SSDs. • This parameter is not available for the ETERNUS DX100 S3/DX200 S3 or the ETERNUS DX200F. enable The EXC function is enabled. (Default value for Open volumes, Standard vol-...
Page 124
The following example creates a Thin Provisioning Volume named "TPV1" in Thin Provisioning Pool#01. The volume type is tpv, and attention is 80%: CLI> create volume -name TPV1 -pool-number 01 -type tpv -size 20gb -attention 80 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
This parameter can be specified when the volume type is TPV. The settable range is 1 – 100%. If this parameter is omitted, attention level is not changed. attention Attention level of the Thin Provisioning Volume (TPV) ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 126
The following example changes the volume named "VOL003" to "VOLUME003", enables copy protection, and changes the attention level to 80: CLI> set volume -volume-name VOL003 -name VOLUME003 -copy-protection enable -attention 80 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example deletes both the volume named "VOL001" and "VOL002" at the same time: CLI> delete volume -volume-name VOL001,VOL002 The following example forcibly deletes NAS TPV #2: CLI> delete volume -volume-number 2 -force ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
RAID groups. Only one RAID group can be specified at the same time. For details, refer to "1.2.9 -rg-name RAID Group Syntax" (page 25). This parameter cannot be specified with the "-pool-number" or the "-pool-name" parameter. rg_number RAID group number rg_name RAID group name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 129
The following example deletes all the volumes contained in the RAID group named "RGP001": CLI> delete all-volumes -rg-name RGP001 The following example deletes all the volumes contained in the Thin Provisioning Pool named "TPP001": CLI> delete all-volumes -pool-name TPP001 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example only formats the volume named "VOL001": CLI> format volume -volume-name VOL001 The following example formats consecutive volumes #80 - #99 at the same time: CLI> format volume -volume-number 80-99 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
This parameter cannot be specified for a Thin Provisioning Volume (TPV). This parameter should be specified when the volume type is NOT a Thin Provisioning Volume (TPV). rg_numbers RAID group number rg_names RAID group name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 132
CLI > expand volume -volume-name VOL001 -rg-number 5,6 -size 800gb,400gb The following example expands the Thin Provisioning Volume named "TPV001" as a new 800GB area: CLI > expand volume -volume-name TPV001 -size 800gb ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
"1.2.9 RAID Group Syntax" (page 25) "1.2.6 Thin Provisioning Pool Syntax" (page 23). rg_number RAID group number rg_name RAID group name pool_number Thin Provisioning Pool number pool_name Thin Provisioning Pool name ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 135
Wide Striping Volume. If omitted, then it is handled as if "auto" is selected. auto The concatenation order for the RAID groups is automatically set. manual The RAID groups are concatenated in the order specified by the "rg-number" or "- rg-name" parameter. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 136
■ Example(s) The following example moves the volume named "VOL003" to the RAID group named "RGP004". The new volume size is 512GB: CLI> start migration -volume-name VOL003 -rg-name RGP004 -size 512gb ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
For details, refer to "1.2.10 Volume Syntax" (page 26). volume_numbers Volume number volume_names Volume name ■ Example(s) The following example stops the RAID migration of volume #1: CLI> stop migration -volume-number 1 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Volume name Balancing Level Balancing level Balancing Process Balancing process Status Balancing process status Progress(%) Balancing process progress Work Volume No. Working volume number Error code Error code Elapsed Time Elapsed time ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 139
----- -------------------------------- --------- ------ ----------- ----------- ----- ------------- 1 TPV01 Medium Active 50 2047 0x00 01h23min45sec <RAID Group List> RAID Group Used No. Name Capacity(MB) --- ---------------- ------------ 1 RAIDGROUP001 1344 2 RAIDGROUP002 2688 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
This parameter specifies the TPV to start balancing. Only one parameter can be specified. For details, refer to "1.2.10 Volume Syntax" (page 26). volume_number Volume number volume_name Volume name ■ Example(s) The following example starts balancing TPV01: CLI> start balancing-thin-po-bolume -volume-name TPV01 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
For details, refer to "1.2.10 Volume Syntax" (page 26). volume_numbers Volume number volume_names Volume name ■ Example(s) The following example stops balancing TPV01 and TPV02: CLI> stop balancing-thin-pro-volume -volume-name TPV01,TPV02 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example starts Zero Reclamation for a TFV that is named "FTV0001": CLI> start zero-reclamation -volume-name FTV0001 The following example starts Zero Reclamation for volumes #80 – #99 at the same time: CLI> start zero-reclamation -volume-number 80-99 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example stops Zero Reclamation for a TFV that is named "FTV0001": CLI> stop zero-reclamation -volume-name FTV0001 The following example stops Zero Reclamation for volumes #80 – #99 at the same time: CLI> stop zero-reclamation -volume-number 80-99 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
All Volumes including volumes with a bandwidth limit of "0" (no upper limit). ■ Output Volume Volume identifiers Volume number Name Volume name Bandwidth Limit QoS performance bandwidth limit (upper limit performance value) configured in the volume ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 145
100 VOL00100 1000 VOL01000 10000 VOL10000 The following example displays the QoS performance setting for volume #1: CLI> show volume-qos -volume-number 1 Volume Bandwidth Limit Name ----- -------------------------------- --------------- 1 VOL00001 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 147
The following example configures the QoS performance setting for the volume named "FTV0001": CLI> set volume-qos -volume-name FTV0001 -bandwidth-limit 0 The following example configures the QoS performance setting for volume #80 – #82: CLI> set volume-qos -volume-number 80-82 -bandwidth-limit 13,14,15 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
FTV that is to be created is preferentially allocated. If this parameter is omitted or "auto" is specified for this parameter, the allocated FTSP is determined automatically. ftsp_number FTSP number auto The allocated FTSP is determined automatically. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 150
The following example creates an FTV. FTRP#0 is set for the FTRP to which the FTV is preferentially allocated, 80% is set for the Attention level threshold, and the copy destination volume protection function is enabled: CLI> create flexible-tier-volume -name FTV0002 -ftrp-number 0 -attention 80 -copy-protection enable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
"enable" is specified, the target FTV cannot be specified as the copy destination. When "disable" is specified, the target FTV can be specified as the copy destination. If omitted, the setting remains unchanged. enable The FTV is protected. disable The FTV is not protected. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 152
The following example changes the FTSP to which the target FTV is preferentially allocated to volume#03, sets the Attention level threshold to 60%, and enables the copy destination volume protection function for volume#02 (FTV): CLI> set flexible-tier-volume -volume-number 2 -priority 3 -attention 60 -copy-protection enable ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example formats an FTV named "FTV0001". CLI> format flexible-tier-volume -volume-name FTV0001 The following example formats consecutive volumes #80 – #99 at the same time: CLI> format flexible-tier-volume -volume-number 80-99 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
FTV capacity (in TB, GB, or MB) ■ Example(s) The following example expands the FTV named "FTV0001" as a new 800GB area: CLI > expand flexible-tier-volume -volume-name FTV0001 -size 800gb ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
The following example deletes an FTV named "FTV0001": CLI> delete flexible-tier-volume -volume-name FTV0001 The following example deletes consecutive volumes #80 – #99 at the same time: CLI> delete flexible-tier-volume -volume-number 80-99 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
24). ftrp_numbers FTRP number ftrp_names FTRP name ■ Example(s) The following example deletes all the FTVs for which an FTRP that is named "FTRP001" is allocated. CLI> delete all-flexible-tier-volumes -ftrp-name FTRP001 ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
If this parameter is omitted or "auto" is specified for this parameter, the allocated FTSP is determined automatically by the ETERNUS DX. ftsp_number FTSP number auto The allocated FTSP is determined automatically. ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Page 158
FTSP#0004. (The volume type of the FTV that is named "FTV0001" remains FTV. The name of the volume remains unchanged.) CLI> start flexible-tier-migration -volume-name TPV000A -ftrp-number 4 -priority auto ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...
Operation mode for the Offloaded Data Transfer function (Disable: disabled, Enable: enabled) ■ Example(s) The following example displays the operation mode for the Offloaded Data Transfer function: CLI> show odx-mode Offloaded Data Transfer Mode [Enable] ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0...