This manual is written for controller firmware versions V10L40 and later. (V10L25 and later when using the ETERNUS DX60 S3. V10L32 and later when using the ETERNUS DX100 S3/DX200 S3, the ETERNUS DX500 S3/ DX600 S3, and the ETERNUS DX200F. V10L33 and later when using ETERNUS DX storage systems in a Unified Storage environment.) Some of the functions herein may not be supported for firmware versions V10L31 and...
Page 6
This manual describes the installation and the environmental settings for the ETERNUS DX storage systems. For basic settings that are not described in this manual, refer to "FUJITSU Storage ETERNUS DX60 S3 Disk storage system Configu- FUJITSU Storage ETERNUS DX ration Guide (Basic)", "FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage...
Page 7
Microsoft® Windows Server® 2012 R2 Essentials • Oracle Solaris might be described as Solaris, Solaris Operating System, or Solaris OS. • Trademark symbols such as and ™ are omitted in this document. ® ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 8
The following naming conventions describe ETERNUS Disk storage system models in this manual. ETERNUS Disk storage system model Naming conventions ETERNUS DX60 S3/DX100 S3/DX200 S3 Disk storage system, storage system ETERNUS DX500 S3/DX600 S3 Disk storage system, ETERNUS DX8700 S3/DX8900 S3 Disk storage system,...
Page 9
Note that the screen shots in this manual were captured during development of the software and the actual screens may be different. Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
7.0, 8.0, 9.0, 10.0 (desktop version), 11.0 (desktop version) Mozilla Firefox 3.6.x, ESR 10.0.x, ESR 17.0.x, ESR 24.0.x Display resolution – • 1024 × 768 or more • 24-bit color or more is recommended ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 11
On the Internet Options Advanced tab, scroll to Security, and select [Use SSL3.0] or [Use TLS1.0]. • On the Internet Options Advanced tab, scroll to Security, and clear the [Do not save encrypted pages to disk] checkbox. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 21
Appendix D Supported Functions for Each Controller Firmware Version 1039 Appendix E Naming Conventions of Volumes and Hosts 1052 Naming Convention of Volumes..................1052 Naming Convention of Hosts ..................1053 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 22
Storage Migration Setting Files 1074 Template File for Storage Migration Settings..............1074 Coding Conventions for the Storage Migration Setting File ..........1077 Setting Example of the Storage Migration Setting File ..........1079 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Initial Setup 1 Performs the minimum settings required before using the ETERNUS DX. Refer to "Initial Setup 1" in "FUJITSU Storage ETERNUS DX Configuration Guide (Web GUI)" for details. The "Initial Setup 1" provides the following functions. Set Storage System Name...
Each parameter is not entered • Each parameter fails to satisfy the input conditions • The old password is different from the current password • "New Password" does not match "Confirm New Password" ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 29
A confirmation screen appears. Click the [OK] button. Changing of the user password starts. Click the [Done] button to return to the [System] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The main setting item is as follows. ● SSH Public Key Setting • SSH Public Key To delete the SSH client public key, select the "Delete" checkbox and click the [Set] button. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 31
A confirmation screen appears. Click the [OK] button. The registration of the SSH public key starts. Click the [Done] button to return to the [System] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For details on the parameters for this function, refer to "A.1.3.1 Modify Storage System Name" (page 667). The procedure to change the storage system name is as follows: Procedure Click [Modify Storage Name] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 33
A confirmation screen appears. Click the [OK] button. Setting of the storage system name starts. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Modify Date and Time" (page 972). The procedure to set the date and time is as follows: Procedure Click [Modify Date and Time] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 35
● Daylight Saving Time Settings • • Range (By day of the week) • Range (By Date) ● NTP Settings • NTP server • LAN Port used for NTP ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 36
When "By Date" is selected for the range of daylight saving time, "Last Day" can be selected to specify the start or end date. Click the [Set] button. A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For details on the parameters for this function, refer to "A.1.3.3 Change Box ID" (page 671). For the factory default settings for this function, refer to "Appendix B Change Box ID" (page 972). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 38
If the Box ID entered is less than 40 characters, a "#" hash key character is appended to the Box ID for each character short. Then, the 40-digit Box ID is registered in the ETERNUS DX. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Setup Subsystem Parameters" (page 973). The procedure to set the subsystem parameters is as follows: Procedure Click [Setup Subsystem Parameters] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 40
A confirmation screen appears. Click the [OK] button. Setting of the subsystem parameter starts. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the ETERNUS DX200 S3 and the ETERNUS DX500 S3/DX600 S3 It is highly recommended that the encryption mode is set to "Fujitsu Original Encryption". When using the encryption function, set the encryption mode to "Fujitsu Original Encryption" or "AES". For details on the parameters for this function, refer to "A.1.3.5 Setup Encryption Mode"...
Page 42
The encryption mode setting is performed. Click the [Done] button to return to the [System Settings] screen. When disabling the encryption mode, reboot the ETERNUS DX. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The procedure to enable or disable the SMI-S function is as follows: ■ Enabling or disabling the SMI-S function when the controller firmware version is V10L2x or earlier (ETERNUS DX60 S3) Procedure Click [Setup SMI-S Environment] in [Action]. ETERNUS Web GUI User’s Guide (Settings)
Page 44
The SMI-S setting is performed. Click the [Done] button to return to the [System Settings] screen. Reboot the ETERNUS DX to apply the new setting. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 45
Chapter 1 System Management 1.4 System Management ■ Enabling the SMI-S when the controller firmware version is V10L30 or later (other than the ETERNUS DX60 S3) Procedure Click [Setup SMI-S Environment] in [Action]. Click the [Start] button. A confirmation screen appears.
Page 46
Chapter 1 System Management 1.4 System Management ■ Disabling the SMI-S when the controller firmware version is V10L30 or later (other than the ETERNUS DX60 S3) Procedure Click [Setup SMI-S Environment] in [Action]. Click the [Stop] button. A confirmation screen appears.
SEDs are used to prevent the leakage of the stored data when physically removed disks are stolen or lost. • The ETERNUS DX60 S3 does not support this function. • Register the SED authentication key before installing SEDs in the ETERNUS DX. If a SED is installed without registering the SED authentication key, data leakage in a SED that is removed may occur.
"Appendix B Setup Power Management" (page 974). The procedure to perform power management setting is as follows: Procedure Click [Setup Power Management] in [Action]. Specify the parameters. ■ For the ETERNUS DX8700 S3/DX8900 S3 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 49
A confirmation screen appears. Click the [OK] button. Setting of the power management starts. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The cache hit rate of EXC or EXCP for each volume can be checked in the [Performance Information] screen. Refer to "Performance (Host I/O)" or "Performance (Advanced Copy)" in "ETERNUS Web GUI User's Guide (Operation)" for details. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 51
When Setting the EXC The target of the EXC setting is the ETERNUS DX500 S3/DX600 S3 and the ETERNUS DX8700 S3/DX8900 S3. Procedure Click [Setup Extreme Cache] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 52
■ For the ETERNUS DX8700 S3/DX8900 S3 ■ For the other models The main setting items are as follows. ● Extreme Cache Memory Size Settings • New Memory Size (for the ETERNUS DX500 S3/DX600 S3) ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 53
"Total PFM Size". Click the [OK] button. The EXC setting starts. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 54
SSDs in the RAID group is adjusted to the SSD of the lowest interface speed. Procedure Click [Setup Extreme Cache] in [Action]. Select "Extreme Cache Pool" for "Cache Used". ■ For the ETERNUS DX8700 S3/DX8900 S3 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 55
Chapter 1 System Management 1.4 System Management ■ For the other models Click the [Memory Size] link for the CM to set an EXCP. ■ For the ETERNUS DX8700 S3/DX8900 S3 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 56
CM where the EXCP memory size is to be set are displayed. For the other models, unused SSDs in the ETERNUS DX are displayed. The main setting items are as follows. • Checkbox to select drives ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 57
Checkbox to select drives Click the [OK] button. Returns to the [Extreme Cache Settings] screen. To set EXCP memory sizes in multiple CMs, repeat Step 3 through Step ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 58
1.4 System Management Check the EXCP memory size, and click the [Set] button. ■ For the ETERNUS DX8700 S3/DX8900 S3 ■ For the other models A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For details on the parameters for this function, refer to "A.1.3.9 Setup Exclusive Read Cache" (page 688). For the factory default settings for this function, refer to "Appendix B Setup Exclusive Read Cache" (page 975). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 60
A confirmation screen appears. Click the [OK] button. The exclusive read cache setting starts. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The procedure to enable or disable the disk patrol function is as follows: Procedure Click [Setup Disk Patrol] in [Action]. Specify whether to enable or disable the disk patrol function. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
"Appendix B Setup Debug Mode" (page 975). The procedure to set the collection conditions for the storage system information is as follows: Procedure Click [Setup Debug Mode] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 63
A confirmation screen appears. Click the [OK] button. The debug mode is set. Click the [Done] button to return to the [System Settings] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
ETERNUS DX is complete. ■ Shutdown the ETERNUS DX The procedure to shut down the ETERNUS DX is as follows: Procedure Click [Shutdown/Restart] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 65
Note that the ETERNUS DX may reboot automatically when "Setup Power Management" is enabled. End of procedure ■ Restart the ETERNUS DX The procedure to restart the ETERNUS DX is as follows: Procedure Click [Shutdown/Restart] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Backup Configuration" (page 975). The procedure to backup configuration definition file is as follows: Procedure Click [Backup Configuration] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 67
A confirmation screen appears. Click the [OK] button. The configuration definition data is backed up. Click the [Done] button to return to the [Utility] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The default file name is "Conf_serial number for the ETERNUS DX_YYYY-MM-DD_hh-mm-ss.cfg". (YYYY-MM-DD_hh-mm-ss: the date and time when the download screen (Step 2) is displayed.) The configuration information is exported. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The procedure to start or stop performance monitoring is as follows: ■ Starting performance monitoring The [Start] button is displayed when the "Monitoring State" is "Stopped". Procedure Click [Start/Stop Perfmon] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 70
The [Stop] button is displayed when "Monitoring State" is "Active". Procedure Click [Start/Stop Perfmon] in [Action]. If the [Stop] button is clicked after starting performance monitoring from other monitoring software, an error screen is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Multiple cache data to be cleared can be selected from "CM", "EXC (*1)", and "EXCP" (*1). Among the "EXC" and "EXCP", only the enabled cache can be the target for clearing. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 72
For details on the parameters for this function, refer to "A.1.4.3 Clear Cache" (page 691). For the factory default settings for this function, refer to "Appendix B Clear Cache" (page 975). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 73
The PFM status is not normal (when selecting "Extreme Cache") • The status of RAID groups registered as EXCPs is not normal (when selecting "Extreme Cache Pool") • Dirty data exists in the cache memory ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 74
Chapter 1 System Management 1.5 Utility Management Click the [OK] button. The cache data is cleared. Click the [Done] button to return to the [Utility] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
"Appendix B Modify Eco-mode General Setting" (page 976). The procedure to set the Eco-mode schedule for a RAID group is as follows: Procedure Click [Modify Eco-mode Setting] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
This function specifies the disk operating time (term for activating disk motor constantly) as an Eco-mode schedule. • Up to 64 Eco-mode schedules can be created for each storage system. • Up to eight events can be specified for a single Eco-mode schedule. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 77
"Appendix B Create Eco-mode Schedule" (page 976). The procedure to create an Eco-mode schedule is as follows: Procedure Click [Create Schedule] in [Action]. Specify the schedule name, and click the [Add Event] button. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 78
The period is set to include Sunday • The period is 1 week or longer (the end date is set to "7 days" when the end time is later than the start time) ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 79
"Schedule Name" matches with an existing schedule name Click the [OK] button. Creation of the Eco-mode schedule starts. Click the [Done] button to return to the [Eco-mode] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
If a disk is activated more than a set amount of times in a day: A state of increased access frequency is assumed and the Eco-mode will cease stopping the disk motor. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 81
Select the Eco-mode schedule that is to be edited and click [Modify Schedule] in [Action]. Select the event that is to be modified and click the [Edit Event] button. Modify the event content. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 82
When deleting the event, select the target event(s) that is to be deleted, and click the [Delete] button. Click the [Apply] button. The "Event List" is updated. Repeat Step 2 through Step 4 to edit multiple events. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 83
"Schedule Name" matches with an existing schedule name Click the [OK] button. Modification of the Eco-mode schedule starts. Click the [Done] button to return to the [Eco-mode] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For details on the parameters for this function, refer to "A.1.6.1 Setup User Account" (page 695). For the factory default settings for this function, refer to "Appendix B Setup User Account" (page 977). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 85
1.7 User Management ■ Add User Account The procedure to add a user accounts is as follows: Procedure Click [Setup User Account] in [Action]. Click the [Add] button. Specify the parameters. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 86
Click the [Done] button to return to the [Define Role] screen. End of procedure ■ Edit User Account The procedure to edit a user accounts is as follows: Procedure Click [Setup User Account] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 87
The main setting items are as follows. ● Edit User Account • Change Password • New Password • Confirm New Password • Role • Account • SSH Public Key ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 88
Delete User Account The procedure to delete a user accounts is as follows: Procedure Click [Setup User Account] in [Action]. Select the deletion target user accounts (multiple selections can be made). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
When the user accounts are initialized, the SSH client public keys for all the users registered in the ETERNUS DX are also deleted. The procedure to initialize user accounts is as follows: Procedure Click [Initialize User Account] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
This is the standard authentication type. Internal Authentication uses user account information stored in the storage system to verify the input user account. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 91
● Primary Server (required) / Secondary Server • Domain Name / IP Address • Port No. • LAN Port • Authentication Mode • Shared Secret • Retry Out Time ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Local Advanced Copy setting functions, Remote Advanced Copy setting functions, etc. Copy Session Management Advanced Copy session management functions (start/stop/delete), etc. Storage Migration Management Storage Migration setting functions (start/suspend/stop/restart/delete path), etc. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 93
For the factory default settings for this function, refer to "Appendix B Add Role" (page 977). The procedure to add a user role is as follows: Procedure Click [Add Role] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 94
A confirmation screen appears. Click the [OK] button. Application of the role settings starts. Click the [Done] button to return to the [Define Role] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
• A role without any policies cannot be created. • The [Modify Role] function can be used when a custom role is created. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 96
A confirmation screen appears. Click the [OK] button. Modification of the role settings starts. Click the [Done] button to return to the [Define Role] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
RMT port The RMT port is used when the line must be separated from the MNT port. For the ETERNUS DX60 S3/DX100 S3/DX200 S3 and the ETERNUS DX200F, this port is also used for maintenance of the ETERNUS DX. •...
Page 98
• Modify Date and Time (NTP settings) • Hot controller firmware upgrade (cold controller firmware upgrade is available) • Add Memory • Add Channel Adapter and Remove Channel Adapter ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 99
The procedure to set network environment using IPv4 address is as follows: Procedure Select which port to set the network environment for, and click [Setup Network Environment] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 100
Speed and Duplex • Wake on LAN ● Interface • Master IP Address • Slave IP Address • Subnet Mask • Gateway ● • Primary DNS • Secondary DNS ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 101
The main setting items are as follows. ● Allowable IP Address Settings • IP Address • Subnet Mask Click the [OK] button. Returns to the [Setup Network Environment] screen. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 102
Slave CM when an error occurs and the Master CM cannot be connected. After registering the allowable IP addresses is complete, click the [Set] button. A confirmation screen appears. Click the [OK] button. The network environment setting starts. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 103
If the gateway is specified, the information of the remote storage systems for which network access will be allowed can be input. The main setting items are as follows. ● • Speed and Duplex • Wake on LAN ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 104
Prefix", and "Gateway". Input the IPv6 address of the Domain Name System (DNS) server if required. To allow access from a different subnetwork to the ETERNUS DX, click the [Add] button. The [Add Allowable IP Address] screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 105
The main setting items are as follows. ● Allowable IP Address Settings • Connect IP Address • Length of Subnet Prefix Click the [OK] button. Returns to the [Setup Network Environment] screen. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 106
Slave CM when an error occurs and the Master CM cannot be connected. After registering the allowable IP addresses is complete, click the [Set] button. A confirmation screen appears. Click the [OK] button. The network environment setting starts. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 107
(3) Replacement of a block with consecutive zeros by "::" is performed only once. [Example] 2001:1000:120:0:0:123:0:0 2001:1000:120::123:0:0 is OK 2001:1000:120::123:: is not allowed (Replacement of a block with consecutive zeros by "::" is allowed only once.) ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 108
"Network Address" and "Subnet Mask". IP Address: 10.20.30.0 Subnet Mask: 255.255.255.0 For IPv6, "IP Address" corresponds to "Connect IP Address", and "Subnet Mask" corresponds to "Length of Subnet Prefix". ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
RMT port The RMT port is used when the line must be separated from the MNT port. For the ETERNUS DX60 S3/DX100 S3/DX200 S3 and the ETERNUS DX200F, this port is also used for maintenance of the ETERNUS DX. •...
Page 110
• Maintenance-Secure • SNMP • RCIL • ETERNUS DX Discovery Click the [Set] button. A confirmation screen appears. Click the [OK] button. Setting of the firewall starts. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
27), the SNMP Agent environment can be configured with the wizard. Refer to "Initial Setup" in "FUJITSU Storage ETERNUS DX Configuration Guide (Web GUI)". When the [Initial Setup] function is not used, configure the SNMP Agent environment in the following order:...
Page 112
A confirmation screen appears. Click the [OK] button. Setting of the SNMP Agent basic interface starts. Click the [Done] button to return to the [Network] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
When adding a Manager IP address, click the [Add] button. Click the [Manager] link to edit the Manager IP address. To delete the existing Manager IP address, click the [Delete] button for the target IP address. The [Manager] screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 114
Repeat Step 2 through Step 4 when registering several Manager IP addresses. After adding or editing the Manager IP address, click the [Set] button. A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
"Appendix B Setup SNMP Agent MIB Access View" (page 981). The procedure to change the SNMP Agent MIB view is as follows: Procedure Click [Setup SNMP MIB View] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 116
The [MIB Access View] screen appears. Add or edit the MIB View The main setting items are as follows. ● MIB Access View • View Name • Subtree1 - Subtree10 ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
This function must be used when using SNMPv3 in SNMP communication between the SNMP Agent and the SNMP Manager. This setting is not necessary when SNMPv1 or SNMPv2c is used for SNMP communication. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 118
When adding a user, click the [Add] button. Click the [User Name] link to edit the user. To delete the existing user, click the [Delete] button for the target user. The [Setup SNMP Agent User] screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 119
Encryption Method • Encryption Password • Retype Encryption Password Click the [OK] button. Returns to the original screen. Repeat Step 2 through Step 4 to configure several users. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Agent and the SNMP Manager. This setting is not necessary when using SNMPv3 only. The SNMP Managers which are allowed to access, and the MIB access range, can be specified for each community. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 121
When adding a community, click the [Add] button. Click the [Community Name] link to edit the community. To delete the existing community, click the [Delete] button for the target community. The [Setup SNMP Agent Community] screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 122
Returns to the original screen. Repeat Step 2 through Step 4 to configure several communities. After adding or editing the community, click the [Set] button. A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Setup SNMP Agent Trap" (page 981). The procedure to set the SNMP Agent trap is as follows: Procedure Click [Setup SNMP Trap] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 124
Add or edit the trap information. The main setting items are as follows. ● Setup SNMP Agent Trap • Manager No. • SNMP Version • Community Name • User Name • Port No. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 125
A confirmation screen appears. Click the [OK] button. Setting of the SNMP Agent Trap starts. Click the [Done] button to return to the [Network] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Download MIB File • Option • Version Click the [Download] button. A confirmation screen appears. Click the [OK] button. A dialog box to download the file appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Chapter 1 System Management 1.8 Network Management Save the downloaded file. The default file name is as follows. • For the ETERNUS DX60 S3/DX100 S3/DX200 S3 FJDARY-E150.MIB • For the ETERNUS DX500 S3/DX600 S3 FJDARY-E150.MIB • For the ETERNUS DX8700 S3/DX8900 S3 FJDARY-E152.MIB...
Page 128
Click the [Done] button to return to the [Network] screen. Confirm that the trap has been successfully received by SNMP Manager after the SNMP Trap test has been performed. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Check the displayed "Event Type" and the "Communication Log". Click the [Refresh] button to update to the latest screen. Click the [Cancel] button to return to the [Network] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Setup E-Mail Notification" (page 982). The procedure to set a E-Mail notification is as follows: Procedure Click [Setup E-Mail Notification] in [Action]. Specify the parameters. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 131
"Notification E-Mail", the settings must be saved when settings such as the destination E-Mail address are changed.) 2. Restart this function and then click the [Send Test E-Mail] button. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Setup Syslog" (page 982). The procedure to set up the Syslog is as follows: Procedure Click [Setup Syslog] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 133
Click the [Set] button. A confirmation screen appears. Click the [OK] button. Setting of the Syslog starts. Click the [Done] button to return to the [Network] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The procedure to set SSH server key is as follows: Procedure Click [Setup SSH Server Key] in [Action]. Specify the parameters. The main setting item is as follows. ● SSH Server Key Setting • Key Length ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
ETERNUS Web GUI via the HTTPS connection. • Refer to "Appendix Installing the Security Certificate" in "FUJITSU Storage ETERNUS DX Configuration Guide (Web GUI)" for procedure to install the self-signed SSL certificate. •...
Page 136
When all of the required items are not input Click the [Create] button. A confirmation screen appears. Click the [OK] button. Creation of the self-signed SSL certificate starts. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Create Key/CSR" (page 982). The procedure to create a CSR is as follows: Procedure Click [Create Key/CSR] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 138
A confirmation screen appears. Click the [OK] button. The creation of the CSR starts. When the creation of the CSR is complete, the screen for downloading the file is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 139
Step 5 Step 7 for each server key file and CSR file that is to exported. Click the [Done] button to return to the [Network] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The SSL server key downloaded using the procedure in "1.8.16 Create Key/CSR" (page 137) and the "SSL server certificate" acquired from the certification authority are required before this action. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 141
Click the [Browse...] button to specify the path to the "SSL Server Key File". The main setting item is as follows. ● Register SSL Certificate Setting • SSL Server Key File Click the [Import] button. "Imported" is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 142
Click the [Browse...] button to specify the path to the "SSL Server Certificate File". The main setting item is as follows. ● Register SSL Certificate Setting • SSL Server Certificate File Click the [Import] button. "Imported" is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 143
ETERNUS DX before being accessed from ETERNUS Web GUI via the HTTPS connection. Log out from ETERNUS Web GUI and wait a few minutes before logging in again. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For the factory default settings for this function, refer to "Appendix B Setup Event Notification" (page 983). The procedure to set the event notification is as follows: Procedure Click [Setup Event Notification] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 145
LCD message on the Overview screen and the Operation Panel. ■ Setting based on Severity (for the ETERNUS DX8700 S3/DX8900 S3) ■ Setting based on Severity (for the other models) ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 146
The main setting items are as follows. ● Setting based on Severity • All Error Events • All Warning Events • All Informational Events ■ Error Severity Level ■ Warning Level ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 147
A confirmation screen appears. Click the [OK] button. Setting of the event notification starts. Click the [Done] button to return to the [Event/Dump] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
All event logs are deleted in a single operation. ■ Display event logs The procedure to display event logs is as follows: Procedure Click [Display/Delete Event Log] in [Action]. Check the displayed event logs. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 149
Click the [Cancel] button to return to the [Event/Dump] screen. End of procedure ■ Delete event logs The procedure to delete event logs is as follows: Procedure Click [Display/Delete Event Log] in [Action]. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The various pieces of maintenance information are combined together, compressed, and then segmented into the user specified segment size before being exported. Special tools to read these logs are required. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 151
When the input date and/or time are not valid (For example: February 31st) • When the end time is earlier than the start time Click the [Export] button. A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 152
After finishing saving each segment, save the following segment immediately. If the log file is segmented, download and save the next segment (save all the segmented files). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 153
Click [Export/Delete Log] in [Action]. Export the storage system log. Set the detailed information for exporting a log. For setting items, refer to Step 2 For a SAN environment. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 154
If "Non-segmentation" is selected in the "Log File Size" field, the [Download] button becomes inactive after the log file has been saved. Proceed to Step 2-5. A dialog box to download the file appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 155
A confirmation screen appears. Click the [OK] button. Log export starts. The progress screen is displayed. After the log export is finished, a screen to execute downloading the file is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 156
When saving segmented log files, make sure to save the segment within five minutes. If five minutes pass before saving the next segment, the log export fails. After finishing saving each segment, save the following segment immediately. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 157
Click the [Download] button to save the exported log. A dialog box to download the file appears. When exporting the log is complete, save the log file immediately. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
For details on the parameters for this function, refer to "A.1.8.3 Export/Delete Panic Dump" (page 750). For the factory default settings for this function, refer to "Appendix B Export/Delete Panic Dump" (page 983). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 159
Click the [OK] button. Exporting of the panic dump starts. The progress screen is displayed. After the panic dump export is finished, a screen to execute downloading the file is displayed. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 160
After finishing saving each segment, save the following segment immediately. If the panic dump file is segmented, download and save the next segment (save all the segmented files). ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
Page 161
Chapter 1 System Management 1.9 Event/Dump Management Click the [Finish] button. A confirmation screen appears. Click the [OK] button to return to the [Event/Dump] screen. End of procedure ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...
The procedure to enable the audit log function is as follows: Procedure Click [Enable Audit Log] in [Action]. If the audit log function has already been enabled, [Enable Audit Log] cannot be clicked. A confirmation screen appears. ETERNUS Web GUI User’s Guide (Settings) Copyright 2015 FUJITSU LIMITED P2X0-1270-13ENZ0...