H: Terminal Function Selection; H1: Digital Inputs - YASKAWA CIPR-GA50C series Technical Manual

12.8

H: Terminal Function Selection

H parameters set functions for external input and output terminals.
◆

H1: Digital Inputs

H1 Parameters set the MFDI terminal functions.
■
H1-01 to H1-07 Terminal S1 to S7 Function Selection
The drive has 7 MFDI terminals. Refer to
No.
H1-01 Terminal S1 Function Selection
H1-02 Terminal S2 Function Selection
H1-03 Terminal S3 Function Selection
H1-04 Terminal S4 Function Selection
H1-05 Terminal S5 Function Selection
H1-06 Terminal S6 Function Selection
H1-07 Terminal S7 Function Selection
*1 The value in parentheses identifies the default setting when you set A1-03 = 3330 [Initialize Parameters = 3-Wire Initialization].
Refer to the and use H1-xx [MFDI Function Select] to set the function.
Refer to the Table 12.55 and use H1-xx [MFDI Function Select] to set the function.
Setting Value
*1
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2 Selection
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog Reference Selection
7 Accel/Decel Time Selection 1
*1
8 Baseblock Command (N.O.)
*1
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Overheat Alarm (oH2)
C Analog Terminal Enable Selection
E ASR Integral Reset
F Through Mode
10 Up Command
11 Down Command
*1
12 Forward Jog
*1
13 Reverse Jog
14 Fault Reset
*1
15 Fast Stop (N.O.)
16 Motor 2 Selection
*1
17 Fast Stop (N.C.)
18 Timer Function
19 PID Disable
YASKAWA SIEPC71061753A GA500 Technical Manual
Table 12.54
Table 12.54 MFDI Default Settings and Functions
Name
Table 12.55 MFDI Setting Values
Function Reference
602
603
604
604
604
604
604
604
604
605
605
605
605
606
606
606
607
608
608
608
609
609
610
610
610

12.8 H: Terminal Function Selection

for drive default settings and functions.
Default
*1
40 (F) Forward RUN (2-Wire)
*1
41 (F) Reverse RUN (2-Wire)
24 External Fault (NO-Always-Coast)
14 Fault Reset
*1
3 (0) Multi-Step Speed Reference 1
*1
4 (3) Multi-Step Speed Reference 2
*1
6 (4) Jog Reference Selection
Setting Value
1A Accel/Decel Time Selection 2
*2
1B Programming Lockout
1E Reference Sample Hold
*1
20 to 2F External fault
30 PID Integrator Reset
31 PID Integrator Hold
32 Multi-Step Speed Reference 4
34 PID Soft Starter Disable
35 PID Input (Error) Invert
3E PID Setpoint Selection 1
3F PID Setpoint Selection 2
*1
40 Forward RUN (2-Wire)
*1
41 Reverse RUN (2-Wire)
*1
42 Run Command (2-Wire Sequence 2)
*1
43 FWD/REV (2-Wire Sequence 2)
44 Add Offset Frequency 1 (d7-03)
45 Add Offset Frequency 2 (d7-03)
46 Add Offset Frequency 3 (d7-03)
47 Node Setup (CANopen)
60 DC Injection Braking Command
61 Speed Search from Fmax
62 Speed Search from Fref
63 Field Weakening
*1
65 KEB Ride-Thru 1 Activate (N.C.)
*1
66 KEB Ride-Thru 1 Activate (N.O.)
Function
Function Reference
610
610
611
611
612
612
612
612
613
613
613
613
613
614
614
614
614
614
614
615
615
615
615
615
616
12
599