H3: Analog Inputs - YASKAWA CIPR-GA50C series Technical Manual

11.10 H: Terminal Functions
◆

H3: Analog Inputs

No.
Name
(Hex.)
H3-01 Terminal A1 Signal
Level Select
(0410)
H3-02 Terminal A1 Function
Selection
(0434)
H3-03 Terminal A1 Gain
Setting
(0411)
RUN
H3-04 Terminal A1 Bias
Setting
(0412)
RUN
H3-09 Terminal A2 Signal
Level Select
(0417)
H3-10 Terminal A2 Function
Selection
(0418)
H3-11 Terminal A2 Gain
Setting
(0419)
RUN
H3-12 Terminal A2 Bias
Setting
(041A)
RUN
H3-13 Analog Input FilterTime
Constant
(041B)
H3-14 Analog Input Terminal
Enable Sel
(041C)
H3-16 Terminal A1 Offset
(02F0)
H3-17 Terminal A2 Offset
(02F1)
H3-40 Mbus Reg 15C1h Input
Function
(0B5C)
H3-41 Mbus Reg 15C2h Input
Function
(0B5F)
H3-42 Mbus Reg 15C3h Input
Function
(0B62)
H3-43 Mbus Reg Inputs
FilterTime Const
(117F)
■
H3-xx: MFAI Setting Values
Setting Value Function
0 Frequency Reference
1 Frequency Gain
380
Description
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the input signal level for MFAI terminal A1.
0 : 0 to 10V (Lower Limit at 0)
1 : 0 V to 10 V (Without Lower Limit)
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFAI terminal A1.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the gain of the analog signal input to MFAI terminal A1.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the bias of the analog signal input to MFAI terminal A1.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the input signal level for MFAI terminal A2.
0 : 0-10V (LowLim=0)
1 : 0-10V (Without Lower Limit)
2 : 4 to 20 mA
3 : 0 to 20 mA
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFAI terminal A2.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the gain of the analog signal input to MFAI terminal A2.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the bias of the analog signal input to MFAI terminal A2.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the time constant for primary delay filters on MFAI terminals.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the enabled terminal or terminals when H1-xx = C [MFDI Function Select =
Analog Terminal Enable Selection] is ON.
1 : Terminal A1
2 : Terminal A2
7 : Terminals A1 and A2
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the offset level for analog signals input to terminal A1. Usually it is not necessary
to change this setting.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the offset level for analog signals input to terminal A2. Usually it is not necessary
to change this setting.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the MEMOBUS AI1 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the MEMOBUS AI2 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the MEMOBUS AI3 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the time constant to apply a primary delay filter to the MEMOBUS analog input
terminal.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
The input value from the MFAI terminal set with this function becomes the master frequency reference.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
The drive multiplies the analog frequency reference with the input value from the MFAI set with this function.
Description
YASKAWA SIEPC71061753A GA500 Technical Manual
Default
Ref.
(Range)
0 643
(0, 1)
0 643
(0 - 32)
100.0% 643
(-999.9 - +999.9%)
0.0% 644
(-999.9 - +999.9%)
2 644
(0 - 3)
0 644
(0 - 32)
100.0% 644
(-999.9 - +999.9%)
0.0% 645
(-999.9 - +999.9%)
0.03 s 645
(0.00 - 2.00 s)
7 645
(1, 2, 7)
0 645
(-500 - +500)
0 645
(-500 - +500)
F 646
(4 - 2F)
F 646
(4 - 2F)
F 646
(4 - 2F)
0.00 s 646
(0.00 - 2.00 s)
Ref.
646
646