E4: Motor 2 Parameters - YASKAWA CIPR-GA50C series Technical Manual

12.6 E: Motor Parameters
■
E3-10: Motor 2 Minimum Output Voltage
No.
Name
(Hex.)
E3-10 Motor 2 Minimum Output
Voltage
(0320)
■
E3-11: Motor 2 Mid Point B Frequency
No.
Name
(Hex.)
E3-11 Motor 2 Mid Point B
Frequency
(0345)
Expert
Note:
• Set this parameter to 0.0 to disable the function.
• When you initialize the drive, this parameter is reset to the default value.
■
E3-12: Motor 2 Mid Point B Voltage
No.
Name
(Hex.)
E3-12 Motor 2 Mid Point B
Voltage
(0346)
Expert
Note:
• Set this parameter to 0.0 to disable the function.
• When you initialize the drive, this parameter is reset to the default value.
• The setting value changes automatically when you do Auto-Tuning (rotational and stationary 1 or 2).
■
E3-13: Motor 2 Base Voltage
No.
Name
(Hex.)
E3-13 Motor 2 Base Voltage
(0347)
Expert
Note:
• When you initialize the drive, this parameter is reset to the default value.
• The setting value changes automatically when you do Auto-Tuning (rotational and stationary 1 or 2).
◆

E4: Motor 2 Parameters

E4 parameters [Motor 2 Parameters] set induction motor data. To switch drive operation from one motor to a
different motor, configure motor 2.
Auto-Tuning automatically sets the E4 parameters to the best values for the application. If you cannot do Auto-
Tuning, set the E4 parameters manually.
Note:
E3-xx and E4-xx are available when H1-xx = 16 [MFDI Function Select = Motor 2 Selection].
■
E4-01: Motor 2 Rated Current
No.
Name
(Hex.)
E4-01 Motor 2 Rated Current
(0321)
568
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the minimum output voltage for the motor 2 V/f pattern.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets a middle output frequency for the motor 2 V/f pattern. Set this parameter to adjust the V/f
pattern for the constant output range. Usually it is not necessary to change this parameter.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets a middle output voltage for the motor 2 V/f pattern. Set this parameter to adjust the V/f
pattern for the constant output range. Usually it is not necessary to change this parameter.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the base voltage for the motor 2 V/f pattern. Set this parameter to adjust the V/f pattern for
the constant output range. Usually it is not necessary to change this parameter.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the motor rated current for motor 2 in amps.
Description
Description
Description
Description
Description
YASKAWA SIEPC71061753A GA500 Technical Manual
Default
(Range)
Determined by E3-01
(200 V Class: 0.0 - 255.0 V,
400 V Class: 0.0 - 510.0 V)
Default
(Range)
0.0 Hz
(0.0 - E3-04)
Default
(Range)
0.0 V
(200 V Class: 0.0 to 255.0
V, 400 V Class: 0.0 to 510.0
V)
Default
(Range)
0.0 V
(200 V Class: 0.0 to 255.0
V, 400 V Class: 0.0 to 510.0
V)
Default
(Range)
Determined by o2-04, C6-
01
(10% to 200% of the drive
rated current)