YASKAWA CIPR-GA50C series Technical Manual page 600

12.8 H: Terminal Function Selection
Setting Value
67 Communications Test Mode
68 High Slip Braking (HSB)
6A Drive Enable
75 Up 2 Command
76 Down 2 Command
77 ASR Gain (C5-03) Select
*1
7A KEB Ride-Thru 2 Activate (N.C.)
*1
7B KEB Ride-Thru 2 Activate (N.O.)
*1
7C Short Circuit Braking (N.O.)
*1 Inverse input is not available.
*2 You cannot use H7-01 to H7-04 [Virtual Multi-Function Input 1 to 4] to set this.
■
H1-01: Terminal S1 Function Selection
No.
Name
(Hex.)
H1-01 Terminal S1 Function
Selection
(0438)
Note:
The default setting is F when the drive is initialized for 3-Wire Initialization [A1-03 = 3330].
■
H1-02: Terminal S2 Function Selection
No.
Name
(Hex.)
H1-02 Terminal S2 Function
Selection
(0439)
Note:
The default setting is F when the drive is initialized for 3-Wire Initialization [A1-03 = 3330].
■
H1-03: Terminal S3 Function Selection
No.
Name
(Hex.)
H1-03 Terminal S3 Function
Selection
(0400)
■
H1-04: Terminal S4 Function Selection
No.
Name
(Hex.)
H1-04 Terminal S4 Function
Selection
(0401)
■
H1-05: Terminal S5 Function Selection
No.
Name
(Hex.)
H1-05 Terminal S5 Function
Selection
(0402)
Note:
When you initialize the drive for 3-Wire Initialization [A1-03 = 3330], the default setting is 0.
■
H1-06: Terminal S6 Function Selection
No.
Name
(Hex.)
H1-06 Terminal S6 Function
Selection
(0403)
600
Function Reference
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFDI terminal S1.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the function for MFDI terminal S2.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the function for MFDI terminal S3.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFDI terminal S4.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFDI terminal S5.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFDI terminal S6.
Setting Value
*1
7D Short Circuit Braking (N.C.)
616
7E Reverse Rotation Identifier
616
7F PID Bi-Directional Enable
616
*1
616 90 to 96 DWEZ Digital Inputs 1 to 7
9F DWEZ Disable
618
101 to 19F Inverse Input of 1 to 9F
618
Sets the function of the selected MFDI to operate
618
inversely. To select the function for inverse input,
enter two digits 01 to 9F for the "xx" in "1xx".
618
618
Description
Description
Description
Description
Description
Description
YASKAWA SIEPC71061753A GA500 Technical Manual
Function Reference
Default
(Range)
40
(1 - 1FF)
Default
(Range)
41
(1 - 1FF)
Default
(Range)
24
(0 - 1FF)
Default
(Range)
14
(0 - 1FF)
Default
(Range)
3
(0 - 1FF)
Default
(Range)
4
(0 - 1FF)
619
619
619
619
619
620