YASKAWA CIPR-GA50C series Technical Manual page 363

No.
Name
(Hex.)
F6-11 CC-Link
Communication Speed
(03B7)
F6-14 BUS Error Auto Reset
(03BB)
F6-15 Comm. Option
Parameters Reload
(0B5B)
F6-16 Gateway Mode
(0B8A)
F6-20 MECHATROLINK
Station Address
(036B)
F6-21 MECHATROLINK
Frame Size
(036C)
F6-22 MECHATROLINK Link
Speed
(036D)
F6-23 MECHATROLINK
Monitor Select (E)
(036E)
F6-24 MECHATROLINK
Monitor Select (F)
(036F)
F6-25 MECHATROLINK
Watchdog Error Sel
(03C9)
F6-26 MECHATROLINK
Allowable No of Err
(03CA)
YASKAWA SIEPC71061753A GA500 Technical Manual
Description
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the communication speed for CC-Link communication. Restart the drive after you
change the parameter setting.
0 : 156 kbps
1 : 625 kbps
2 : 2.5 Mbps
3 : 5 Mbps
4 : 10 Mbps
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the automatic reset function for bUS [Option Communication Errors].
0 : Disabled
1 : Enabled
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the update method when you change F6-xx, F7-xx [Communication Options].
0 : Reload at Next Power Cycle
1 : Reload Now
2 : Cancel Reload Request
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the gateway mode operation and the number of connected slave drives.
0 : Disabled
1 : Enabled: 1 Slave Drives
2 : Enabled: 2 Slave Drives
3 : Enabled: 3 Slave Drives
4 : Enabled: 4 Slave Drives
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the station address for MECHATROLINK communication. Change the parameter
then cycle power on the drive.
Note:
• The setting range changes if using MECHATROLINK-II or MECHATROLINK-
III:
–MECHATROLINK-II (SI-T3) range: 20 - 3F
–MECHATROLINK-III (SI-ET3) range: 03 - EF
• Be sure to set a node address that is different than all other node addresses.
Incorrect parameter settings will cause AEr [Station Address Setting Error] errors
and the L.ERR LED on the option will come on.
• The drive detects AEr errors when the station address is 20 or 3F.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the frame size for MECHATROLINK communication. Restart the drive after you
change the parameter setting.
0 : 32byte (M-2) / 64byte (M-3)
1 : 17byte (M-2) / 32byte (M-3)
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the communications speed for MECHATROLINK-II. Restart the drive after you
change the parameter setting.
Note:
This parameter is only available with the MECHATROLINK-II option.
0 : 10 Mbps
1 : 4 Mbps
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the MEMOBUS register used for the monitor functions of INV_CTL (drive
operation control command) and INV_I/O (drive I/O control command). Restart the
drive after you change the parameter setting.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the MEMOBUS register used for the monitor functions of INV_CTL (drive
operation control command) and INV_I/O (drive I/O control command). Restart the
drive after you change the parameter setting.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the method to stop the motor or let the motor continue operating when the drive
detects E5 [MECHATROLINK Watchdog Timer Err].
0 : Ramp to Stop
1 : Coast to Stop
2 : Fast Stop (Use C1-09)
3 : Alarm Only
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the number of times that the option must detect a bUS alarm to cause a bUS
[Option Communication Error].
11.9 F: Options
Default
Ref.
(Range)
0 586
(0 - 4)
0 586
(0, 1)
0 586
(0 - 2)
0 586
(0 to 4)
0021h 587
(MECHATROLINK-II:
0020h - 003Fh,
MECHATROLINK-III:
0003h - 00EFh)
0 587
(0, 1)
0 587
(0, 1)
0000h 587
(0000h - FFFFh)
0000h 587
(0000h - FFFFh)
1 588
(0 - 3)
2 588
(2 - 10 times)
363
11