YASKAWA CIPR-GA50C series Technical Manual page 762

Delete Backed-up Parameters.................................. 132
Restore (keypad to drive) ....................................... 131
Setup Mode ....................................................... 129
User-set ........................................................... 474
Verify (keypad and drive) ...................................... 131
Parameter Change .................................................... 739
Parameter Setting Errors ...................................... 238, 269
PASS ................................................................... 267
Password
Setting ............................................................. 460
Verification ....................................................... 460
PC
Connection procedure ............................................ 92
PE1 ..................................................................... 256
PE2 ..................................................................... 256
Peripheral Devices ................................................... 331
PF................................................................. 256, 267
Protective function .............................................. 704
PGo
Detection time.................................................... 578
Fault ............................................................... 257
Minor Fault ....................................................... 267
Operation Selection after Detection ........................... 576
Phase Order Selection ............................................... 483
PID control ............................................................ 498
control block diagram ........................................... 501
Feedback value input............................................ 500
fine tuning ........................................................ 502
Parameter ......................................................... 504
PID feedback loss detection .................................... 501
PID Sleep ......................................................... 502
Setpoint input .................................................... 499
PM motor
Auto-Tuning ...................................................... 135
PM motor parameters ................................................ 571
d-Axis inductance ............................................... 572
Induced voltage constant 1 ..................................... 572
Induced voltage constant 2 ..................................... 573
Motor rated current ........................................ 191, 571
Motor rated power (kW) ........................................ 571
Number of motor poles ......................................... 572
q-Axis inductance ............................................... 572
Stator resistance.................................................. 572
PM Motors
Fine Adjustment ........................................... 720, 727
Motor Code Selection ........................................... 571
Motor parameters ................................................ 571
Positive Temperature Coefficient (PTC) Thermistor ............ 665
Power loss .......................................................... 33, 36
Programming mode .................................................. 118
Protection Functions
DC bus undervoltage ............................................ 677
Drive Overheating ............................................... 703
HCA ............................................................... 708
Internal Drive Braking Transistor ............................. 708
LF2 ................................................................ 707
Motor Overheating ........................................ 194, 669
Motor Overheating (PTC Input) ......................... 195, 669
Motor Overload ............................................ 191, 665
oC .................................................................. 706
oH.................................................................. 703
oH2 ................................................................ 703
oH3 .......................................................... 194, 669
oH4 .......................................................... 195, 669
Output Current Overload ....................................... 708
Overcurrent ....................................................... 706
rr ................................................................... 708
762
Software Current Limit Selection ............................. 706
Uv1 ................................................................ 677
Protective function
Desynchronization............................................... 709
GF.................................................................. 705
Ground Fault Detection ......................................... 705
Input Phase Detection ........................................... 704
LF .................................................................. 704
Low Speed Desynchronization ................................ 709
LSo ................................................................ 709
oL2................................................................. 706
Output Phase Loss Detection .................................. 704
Overload .......................................................... 706
PF .................................................................. 704
Pulse Train Input
Terminal RP Function Selection ............................... 658
Pulse Train Input/Output
Parameter ......................................................... 658
Pulse train output
Terminal MP function selection ............................... 660
Wiring specifications............................................. 89
PWEr................................................................... 277
R
Rating (400 V)
Drive............................................................... 317
Rating (Single-phase 200 V)
Drive............................................................... 316
Rating (Three-phase 200 V)
Drive............................................................... 314
rdEr ..................................................................... 277
Remove
Front cover ........................................................ 39
Keypad ............................................................. 41
RESET key ............................................................ 113
Residual Current Monitor/Residual Current Device
RCM/RCD......................................................... 96
Wiring .............................................................. 96
Restore
Parameters (keypad to drive)................................... 131
Reverse Operation Selection ........................................ 481
rF ....................................................................... 257
rH ....................................................................... 257
RJ-45 connector ...................................................... 113
Rotational Auto-Tuning
Induction Motor.................................................. 134
PM motor ......................................................... 135
Precautions ....................................................... 139
rr ........................................................................ 257
Protection Functions ............................................ 708
rUn ..................................................................... 267
Run command
LOCAL/REMOTE Run selection ............................. 478
Switching between LOCAL/REMOTE....................... 478
Run Command at Power Up ........................................ 486
Run Command Selection 2
Switching between LOCAL/REMOTE....................... 485
RUN indicator ........................................................ 113
RUN key............................................................... 113
S
S-curve characteristics
Parameter ......................................................... 525
SC ...................................................................... 257
SCF..................................................................... 258
Screen .................................................................. 128
SE....................................................................... 267
SEr...................................................................... 258
YASKAWA SIEPC71061753A GA500 Technical Manual