Siemens G130 List Manual page 1286

n_limit pos eff
From setpoint limiting
r1084
[3050.8]
n_limit neg eff
<5> [3095.7]
r1087
n_act smooth
r0063
[4710.7] <5>
n_act smooth signal
r2169
0...1 000 000 [ms]
p2153 (0)
[8011.1]
[8012.5]
[8013.1]
n_act unsmoothed
r0063[0]
[4715.7] <4>
Smoothing
n_thresh val 3
0.00...210 000.00 [rpm]
p2161[D] (5.00)
1
0
<1>
0.00...300.00 [rpm]
p2150[D] (2.00)
n_hysteresis 3
<1> VECTOR: Calculated.
<2> VECTOR: Depending on the drive unit (250 or 400 μs).
<3> VECTOR: Depending on the drive unit (1000 or 1600 μs).
<4> Only for VECTOR.
<5> Only for SINAMICS S120 and SERVO.
1 2
DO: SERVO, VECTOR
Signals and monitoring functions - Speed signals 1
p0115[1] (125.00 μs)
p0115[1] (<2>)
0 ZSW Monitor 1
n
r2197
r2197.6
n
|n_act| > n_max
F07901
"Motor overspeed"
0.00...60 000.00 [rpm]
p2162[D] (0.00)
p0300 = 5
p1300 = 20
&
p1501 = 1
r0107 = 2
n_thresh val 2
0.00...210 000.00 [rpm]
ZSW seq_ctrl
p2155[D] (900.00)
r0899
1 = Ready
r0899.1
Encoderless operation active
1
n_thresh val 1
0
0.00...210 000.00 [rpm]
p2141[D] (5.00)
<1>
0.00...300.00 [rpm]
p2140[D] (90.00)
1
n_hysteresis 2
1
0
0
<1>
0.000...300.000 [rpm]
p2142[D] (2.00)
n_hysteresis 1
3 4
[2534.3]
1 = Magnetizing
completed
r0056.4
&
Enable underspeed monitoring
p2149.6 = 1
1 = Magnetizing completed
r0056.4
1
&
&
r1407.1
1
T 0
t_on cmpr val rchd
0.0...10 000.0 [ms]
p2156[D] (0.0)
5
fp_8010_54_eng.vsd
01.06.16 V04.08.00
p0115[3] (4000.00 μs)
ZSW Monitor 3
0
r2199
r2199.0
1
|n_act| < p2161
0
0
F07822
Monitoring underspeed
1
threshold fallen below
fault
1
1
A07821
0
Monitoring underspeed
0
threshold fallen below
alarm
ZSW Monitor 1
1
r2197
r2197.1
0
|n_act| <= speed threshold value 2
ZSW Monitor 1
r2197
r2197.2
|n_act| > speed threshold value 2
ZSW Monitor 3
r2199
r2199.1
f or n-comparison value
reached/exceeded
6 7
Function diagram
S120/S150/G130/G150
p0115[3] (<3>)
[2537.3]
[2534.3]
[2534.3]
[2537.3]
8
- 8010 -