Ntp- D154 Convert A Point-To-Point To A Linear Adm Manually - Cisco ONS 15454 SDH Procedure Manual

Chapter 13 Convert Network Configurations
Complete the
Step 1
you are already logged in, continue with Step 2.
Complete the
Step 2
Log into the node that will be added to the point-to-point configuration (the new node).
Step 3
Complete the
Step 4
has two STM-N cards with the same rate as the point-to-point nodes.
Complete the
Step 5
Physically connect the fibers between the point-to-point node and the new node. The fiber connections
Step 6
should be connected working card to working card and protect card to protect card.
On the new node, create a 1+1 protection group for the STM-N cards that will connect to the
Step 7
point-to-point node. See the
Complete the
Step 8
the working STM-N cards in the new node that will connect to the linear ADM network. (Alternatively,
if additional bandwidth is needed for CTC management, complete the
Multiplex-Section DCC Terminations" task on page
state in the Create RS-DCC Termination dialog box to Unlocked.
Note
Display the point-to-point node that will connect to the new node in CTC node view.
Step 9
Complete the
Step 10
point-to-point node has STM-N cards installed that can connect to the new node.
Create a 1+1 protection group for the STM-N cards in the point-to-point node that will connect to the
Step 11
new node. See the
Create DCC terminations on the working STM-N card in the point-to-point node that will connect to the
Step 12
new node. See the
(Alternatively, if additional bandwidth is needed for CTC management, complete the
Provision Multiplex-Section DCC Terminations" task on page
Termination dialog box, set the port administrative state to Unlocked.
From the View menu, choose Go to Node View to display the new node in node view.
Step 13
Complete the
Step 14
using line timing, set the working STM-N card as the timing source.
From the View menu, choose Go to Network View to display the network view to verify that the newly
Step 15
created linear ADM configuration is correct. One green span line should appear between each linear
node.
Click the Alarms tab.
Step 16
Verify that the alarm filter is not on. See the
a.
page 19-25
Verify that no unexplained alarms appear on the network. If alarms appear, investigate and resolve
b.
them before continuing. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide for procedures.
Repeat the procedure to add an additional node to the linear ADM.
Step 17
Stop. You have completed this procedure.
78-17194-01
"DLP-D60 Log into CTC" task on page 17-49
"DLP-D298 Check the Network for Alarms and Conditions" task on page
"NTP-D24 Verify Card Installation" procedure on page 4-2
"NTP-D35 Verify Node Turn-Up" procedure on page 5-2
"DLP-D73 Create a 1+1 Protection Group" task on page
"DLP-D363 Provision Regenerator-Section DCC Terminations" task on page 20-68
DCC failure alarms appear until you create DCC terminations in the point-to-point node.
"NTP-D24 Verify Card Installation" procedure on page 4-2
"DLP-D73 Create a 1+1 Protection Group" task on page 17-64
"DLP-D363 Provision Regenerator-Section DCC Terminations" task on page
"NTP-D28 Set Up Timing" procedure on page 4-9
as necessary.

NTP- D154 Convert a Point-to-Point to a Linear ADM Manually

at one of the two point-to-point nodes. If
to ensure that the new node
for the new node.
"DLP-D364 Provision
20-71.) Make sure to set the port administrative
to ensure that the
20-71.) In the Create RS-DCC
for the new node. If the new node is
"DLP-D227 Disable Alarm Filtering" task on
Cisco ONS 15454 SDH Procedure Guide, R7.0
19-83.
17-64.
for
for instructions.
20-68.
"DLP-D364
13-5