Table of Contents
Advertisement
Quick Links
Install Cards and Fiber-Optic Cable
This chapter explains how to install the Cisco ONS 15454 SDH cards and fiber-optic cable (fiber).
Before You Begin
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1030
Filler cards serve three important functions: they prevent exposure to hazardous voltages and
Warning
currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other
equipment; and they direct the flow of cooling air through the chassis. Do not operate the system
unless all cards and faceplates are in place. Statement 156
78-18118-01
NTP-D15 Install the Common Control Cards, page
any other cards.
NTP-D16 Install STM-N Cards and Connectors, page
NTP-D17 Install the Electrical Cards, page
NTP-D18 Install Ethernet Cards and Connectors, page
NTP-D286 Install the FC_MR-4 Cards, page
NTP-D348 Install the Filler Cards, page
NTP-D349 Install the Blank Faceplates, page
NTP-D19 Install Fiber-Optic Cables on Optical Cards, page
needed.
NTP-D245 Route Fiber-Optic Cables, page
NTP-D227 Remove and Replace a Card, page
and replace a card, including deleting the card from Cisco Transport Controller (CTC) and changing
an optical card without losing the card's provisioning.
NTP-D20 Replace the Front Door, page
procedure to replace the front door and ground strap after installing cards and fiber.
C H A P T E R
2-2—Complete this procedure before installing
2-7—Complete this procedure as needed.
2-10—Complete this procedure as needed.
2-11—Complete this procedure as needed.
2-12—Complete this procedure as needed.
2-14—Complete this procedure as needed.
2-15—Complete this procedure as needed.
2-16—Complete this procedure as
2-19—Complete this procedure as needed.
2-21—Complete this procedure as needed to remove
2-21—If the front door was removed, complete this
Cisco ONS 15454 SDH Procedure Guide, R8.5
2
2-1
Advertisement
Table of Contents
Related Manuals for Cisco ONS 15454 SDH
Summary of Contents for Cisco ONS 15454 SDH
-
Page 1: Before You Begin
C H A P T E R Install Cards and Fiber-Optic Cable This chapter explains how to install the Cisco ONS 15454 SDH cards and fiber-optic cable (fiber). Before You Begin This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs). - Page 2 During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94 Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the Caution wristband cable into the ESD jack located on the lower-right outside to edge of the shelf assembly.
- Page 3 12 to 17, include four slots (Slots 5, 6, 12, and 13) that have four times the bandwidth of the other multiservice slots. Table 2-1 ONS 15454 SDH Card and Slot Compatibility for the XC-VXL-2.5G Cards Slot TCC2/ TCC2/...
- Page 4 Chapter 2 Install Cards and Fiber-Optic Cable NTP- D15 Install the Common Control Cards Table 2-1 ONS 15454 SDH Card and Slot Compatibility for the XC-VXL-2.5G Cards (continued) Slot TCC2/ TCC2/ Type TCC2P XC AIC-I XC TCC2P MS E1-42 E3-12...
- Page 5 Chapter 2 Install Cards and Fiber-Optic Cable NTP- D15 Install the Common Control Cards Table 2-1 ONS 15454 SDH Card and Slot Compatibility for the XC-VXL-2.5G Cards (continued) Slot TCC2/ TCC2/ Type TCC2P XC AIC-I XC TCC2P MS OC192 Not supported with XC-VXL-2.5G cards. Requires XC-VXL-10G or XC-VXC-10G cards.
- Page 6 OC48 IR/STM16 SH AS 1310 OC48 LR/STM16 LH AS 1550 OC48 ELR/STM16 EH 100 GHz OC192 SR/STM64 IO 1310 OC192 IR/STM64 SH 1550 OC192 LR/STM64 LH 1550 OC192 LR/STM64 LH ITU 15xx.xx Cisco ONS 15454 SDH Procedure Guide, R8.5 78-18118-01...
- Page 7 During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94 Cisco ONS 15454 SDH Procedure Guide, R8.5 78-18118-01...
- Page 8 The laser is off when the safety key is off (labeled 0). Statement 293 Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the Caution wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.
- Page 9 OC-48 XC-VXC-10G/XC-VXL-10G OC-48 OC-192 Refer to the card’s reference section in the “Optical Cards” chapter of the Cisco ONS 15454 SDH Reference Manual for more information about slot and bandwidth restrictions. Open the card latches/ejectors. Step 2 Use the latches/ejectors to firmly slide the optical card along the guide rails until the card plugs into the Step 3 receptacle at the back of the slot.
-
Page 10: Table Of Contents
Install higher-capacity cards first; for example, install an E3-12 card before installing an E1-14 card. Let each card boot completely before installing the next card. Cisco recommends installing STM-N, transponder (TXP), and muxponder (MXP) cards before you Note install electrical cards, as applicable. -
Page 11: Step 4
Statement 94 Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products. Statement 291 Warning Cisco ONS 15454 SDH Procedure Guide, R8.5 2-11 78-18118-01... -
Page 12: Step 1 If You Installed Xc-Vxl-2.5G Cards, Review
Ethernet ports to intrabuilding or nonexposed wiring and cabling only. Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the Caution wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly. -
Page 13: If You Install The Wrong Card In A Slot, Complete The Procedure On Page
(for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056 Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the Caution wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly. - Page 14 EMI that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards and faceplates are in place. Statement 156 Cisco ONS 15454 SDH Procedure Guide, R8.5 2-14 78-18118-01...
- Page 15 Always use the supplied ESD wristband when working with a powered ONS 15454_SDH. Plug the Caution wristband cable into the ESD jack located on the lower right outside edge of the shelf assembly and ensure the shelf assembly is properly grounded. Cisco ONS 15454 SDH Procedure Guide, R8.5 2-15 78-18118-01...
- Page 16 Using unattenuated fiber loopbacks causes irreparable damage to the STM64 SH 1550 card. Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the Caution wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.
-
Page 17: Dlp-D335 Install Gbic Or Sfp/Xfp Devices" Task On
(ONS-SC-2G-30.3 0 dBm 4 dBm –28 dBm –9 dBm through ONS-SC-2G-60.6) 15454_MRC-12 (ONS-SI-622-I1) –15 dBm –8 dBm –28 dBm –8 dBm 15454_MRC-12 (ONS-SI-622-L1) –3 dBm 2 dBm –28 dBm –8 dBm Cisco ONS 15454 SDH Procedure Guide, R8.5 2-17 78-18118-01... -
Page 18: Table
“DLP-D42 Install Fiber-Optic Cables on an LGX Interface” task on page 17-31. Step 3 As needed, complete the “DLP-D22 Install Fiber-Optic Cables in a 1+1 Configuration” task on Step 4 page 17-17. Cisco ONS 15454 SDH Procedure Guide, R8.5 2-18 78-18118-01... - Page 19 M IN Route the fiber cable on the card faceplate through the fiber clip on the faceplate (Figure 2-3). Fiber clips Step 3 are factory-attached to the faceplate of the STM-N cards. Cisco ONS 15454 SDH Procedure Guide, R8.5 2-19 78-18118-01...
- Page 20 Use the reversible fiber guides to route cables out the desired side. Step 7 Close the fold-down front door when all fiber cables in the front compartment are properly routed. Stop. You have completed this procedure. Cisco ONS 15454 SDH Procedure Guide, R8.5 2-20 78-18118-01...
- Page 21 Chapter 2 Install Cards and Fiber-Optic Cable NTP- D227 Remove and Replace a Card NTP-D227 Remove and Replace a Card Purpose This procedure removes and replaces cards in the ONS 15454 SDH shelf. Tools/Equipment None Prerequisite Procedures DLP-D60 Log into CTC, page 17-44...
- Page 22 Assembly hinge Swing the door closed. Step 3 The ONS 15454 SDH comes with a pinned hex key tool for locking and unlocking the front door. Note Turn the key counterclockwise to unlock the door and clockwise to lock it.