Toyota Tundra 2005 Service - Repair - Maintenance page 2556

SA−142
Thickness
Mark
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
SUSPENSION AND AXLE
F16243
RA0090
F16243
mm (in.) Mark
2.58 (0.1015) 90
2.60 (0.1024) 92
2.62 (0.1031) 94
2.64 (0.1039) 96
2.66 (0.1047) 98
2.68 (0.1055) 00
2.70 (0.1063) 02
2.72 (0.1071) 04
2.74 (0.1079) 06
2.76 (0.1087) 08
2.78 (0.1094) 10
2.80 (0.1102) 12
2.82 (0.1110) 14
2.84 (0.1118) 16
2.86 (0.1126) 18
2.88 (0.1134) 20
− REAR DIFFERENTIAL CARRIER (w/ LSD)
(j) Using a dial indicator, while holding the companion
flange, measure the ring gear backlash.
Backlash: 0.13 − 0.18 mm (0.0051 − 0.0071 in.)
If the backlash is not within the specified value, adjust it by ei-
ther increasing or decreasing the thickness of washers on both
sides by an equal amount.
HINT:
There should be no clearance between the plate washer and
the case.
Make sure that there is a ring gear backlash.
14. ADJUST SIDE BEARING PRELOAD
(a) Remove the ring gear teeth side plate washer and using
a micrometer, measure the thickness.
(b) Using the backlash as a reference, install a new washer
that is 0.06 − 0.09 mm (0.0024 − 0.0035 in.) thicker than
the washer removed.
HINT:
Select a washer which can be pressed in 2/3 of the way with
your finger.
(c) Using a plastic hammer, install the plate washer.
(d) Recheck the ring gear backlash.
Backlash: 0.13 − 0.18 mm (0.0051 − 0.0071 in.)
If the backlash is not within the specified value, adjust it by ei-
ther increasing or decreasing the thickness of washers on both
sides by an equal amount.
HINT:
The backlash will change by about 0.02 mm (0.0008 in.) corre-
sponding to 0.03 mm (0.0012 in.) change in the plate washer.
Washer thickness:
Thickness
mm (in.)
2.90 (0.1142)
2.92 (0.1150)
2.94 (0.1157)
2.96 (0.1165)
2.98 (0.1173)
3.00 (0.1181)
3.02 (0.1189)
3.04 (0.1197)
3.06 (0.1205)
3.08 (0.1213)
3.10 (0.1220)
3.12 (0.1228)
3.14 (0.1236)
3.16 (0.1244)
3.18 (0.1252)
3.20 (0.1260)
Thickness
Mark
22
24
26
28
30
32
34
36
38
40
42
44
46
48
−
−
mm (in.)
3.22 (0.1268)
3.24 (0.1276)
3.26 (0.1283)
3.28 (0.1291)
3.30 (0.1299)
3.32 (0.1307)
3.34 (0.1315)
3.36 (0.1323)
3.38 (0.1331)
3.40 (0.1339)
3.42 (0.1346)
3.44 (0.1354)
3.46 (0.1362)
3.48 (0.1370)