Brake and Parking Brake Warning Light Symptom Diagnosis
Condition
Brake warning light does
not light up when brake
fluid level is low or
parking brake is pulled up
or for 5 seconds after
turning ON ignition switch
Brake warning light stays
ON
Seat Belt Reminder Light Symptom Diagnosis
Condition
Seat belt reminder light
does not light up
Seat belt reminder light
stays ON
A/T Shift Position Indicator Symptom Diagnosis (A/T Model)
Condition
All A/T shift position
indicator does not light up
Possible cause
Circuit fuse blown
Brake fluid level switch faulty
Parking brake switch faulty
ABS system faulty
Wiring or grounding faulty
Combination meter faulty
BCM faulty
Brake fluid level switch faulty
Parking brake switch faulty
EBD system faulty
Wiring or grounding faulty
Combination meter faulty
BCM faulty
Possible cause
Circuit fuse blown
Seat belt switch faulty
Wiring or grounding faulty
Combination meter faulty
BCM faulty
Seat belt switch faulty
Wiring or grounding faulty
Combination meter faulty
BCM faulty
Possible cause
Circuit fuse blown
Transmission range sensor (shift switch)
faulty
Wiring or ground faulty
Combination meter faulty
TCM faulty
Instrumentation / Driver Info. / Horn:
Correction / Reference Item
Replace fuse and check for short circuit.
Check brake fluid level switch referring to
"Brake Fluid Level Switch Inspection".
Check parking brake switch referring to
"Parking Brake Switch Inspection".
Refer to "ABS Check in Section 4E".
Repair circuit.
Replace combination meter.
Replace after making sure that none of above
parts is faulty.
Check brake fluid level switch referring to
"Brake Fluid Level Switch Inspection".
Check parking brake switch referring to
"Parking Brake Switch Inspection".
Refer to "EBD Warning Light (Brake Warning
Light) Check in Section 4E".
Repair circuit.
Replace combination meter.
Replace after making sure that none of above
parts is faulty.
Correction / Reference Item
Replace fuse and check for short circuit.
Check seat belt switch referring to "Front Seat
Belt Inspection in Section 8A".
Repair circuit.
Replace combination meter.
Replace after making sure that none of above
parts is faulty.
Check seat belt switch referring to "Front Seat
Belt Inspection in Section 8A".
Repair circuit.
Replace combination meter.
Replace after making sure that none of above
parts is faulty.
Correction / Reference Item
Replace fuse and check for short circuit.
Check transmission range sensor referring to
"Transmission Range Sensor Inspection and
Adjustment in Section 5A".
Repair circuit.
Replace combination meter.
Replace after making sure that none of above
parts is faulty.
9C-9
S7RW0A9304007
S7RW0A9304008
S7RW0A9304009
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated
دلایل بالا رفتن مصرف بنزین در مدل اتومات
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated