K Connector; L Connector - Suzuki SX4 Service Manual
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (278 pages) ,
- Owner's manual (18 pages)
Table of Contents
Advertisement
9A-177 Wiring Systems:
J146
J147
1
2
MCONF020008-01
IF EQPD
J154
J215 (L379)
26
25
24
34
23
33
22
32
21
31
2
1
30
MCONM020018-01
29
20
28
19
27
18
17
16
15
IF EQPD
K Connector
K51
K52
1 2 3
MCONF030134-01
K153 (TO G348)
K154 (TO G354)
1
MCONF010010-01
L Connector
L01
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
Except Taiwan
J148
1
2
1
2
MCONF020159-01
MCONF020159-01
IF EQPD
J216 (L380)
26
14
14
25
13
13
24
34
23
12
6
12
33
22
11
5
11
32
21
4
31
30
3
29
20
10
2
10
28
19
9
1
9
27
18
17
8
8
16
7
7
15
MCONM340003-02
MCONM340003-02
K121
1
1
2
2
MCONF020157-01
MCONM020068-01
Hatchback
1
MCONM010040-01
L04
1
2 3 4 5 6 7 8 9 10 11
MCONF180012-01
27 28 29 30 31 32 33 34 35 36
J151
J152
1
2
MCONF020159-01
IF EQPD
J217 (TO L381)
J218 (TO L382)
6
5
1
2
3
4
5
4
6
7
8
9
10
3
MCONF100060-01
2
1
K121
K152 (TO L383)
2
1
MCONM020065-01
Sedan
12 13 14 15 16
37 38 39 40 41
J153
2
1
2
MCONF020159-01
MCONM020018-01
IF EQPD
IF EQPD
1
2
3
4
5
6
7
8
9
10
MCONF100060-01
S7RW0A910F006
K152 (TO L383)
1 2 3
3 2 1
MCONF030134-01
MCONM030021-01
Hatchback
Sedan
S7RW0A910F007
17 18 19 20 21 22 23 24 25 26
42 43 44 45 46 47 48 49 50 51
MCONF510001-01
1
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated
دلایل بالا رفتن مصرف بنزین در مدل اتومات
we bought the car & had no issues besides the filler neck. we changed it & then later on down the road we jumped another car with the suzuki sx4 & after doing it blew the alternator, got new alternator & now if we don't turn headlights on BEFORE you start the car you can hear some pump in the trunk area going on & off. Or you can pull up on the emergency brake one click & it will stop. if you turn off the headlights after it's running the noise will come back. it did NOT do this until we jumped another vehicle, that is what blew the alternator. we have a brand new one in the car now. any ideas of why it's doing this? it seems electrical but we don't know where to begin.
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
A Suzuki SX4 that cranks but does not start with a U0100 code (Lost Communication with ECM/PCM) after the crank sensor wire was repaired could have the following issues:
1. Faulty Engine Swap: The engine may not be compatible or not properly installed, as noted in the context that the problem started after an engine replacement.
2. Crankshaft Sensor Issues: Even after repairing the crank sensor wire, the sensor itself could be faulty or not sending a proper signal.
3. ECU Communication Problem (U0100): This indicates a loss of communication with the ECU, possibly due to wiring faults, poor ground connections, or a damaged ECU.
4. Starter Motor Issues: Although the engine cranks, if the starter motor is weak or has voltage issues (as noted with 11.5V), it may not spin the engine fast enough for it to start.
In summary, the likely causes are improper engine installation, crank sensor signal issues, ECU communication failure, or weak starter motor performance.
This answer is automatically generated
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated