Honda Accord 2008 Manual page 829

07/11/02 09:25:14 61TA0000_130_0056
Manual Transmission
Mainshaft Thrust Clearance Adjustment (cont'd)
11. Zero a dial gauge (A) on the end of the mainshaft.
＊０４
12. Turn the mainshaft holder bolt (B) clockwise; stop
turning when the dial gauge has reached its
maximum movement. The reading on the dial
gauge is the amount of mainshaft thrust clearance.
NOTE: Do not turn the mainshaft holder bolt more
than 60 degrees after the needle of the dial gauge
stops moving. Applying more pressure with the
mainshaft holder bolt could damage the
transmission.
13. If the reading is with in the standard, the clearance
is correct. If the reading is not within the standard,
select the appropriate shim needed from the table,
and recheck the thrust clearance.
Standard: 0.11 0.17 mm (0.004 0.007 in.)
(Example)
Measure reading: 1.93 mm (0.0759 in.)
Subtract the total clearance measurement from the
middle of the clearance standard 0.14 mm
(0.0056 in.).
1.93
Select the shim closest to the amount calculated,
for example the 1.80 mm (0.0709 in.) shim.
14. With oil guide plate M and the appropriate size
shim installed in the transmission housing, check
the thrust clearance again to verify the clearance is
within the standard.
72 mm Shim
A
B
C
D
E
13-56
A
07GAJ-PG20110
07GAJ-PG20130
− −
−
0.14 = 1.79 mm (0.0704 in.)
Part Number Thickness
23931-P21-000 0.60 mm (0.024 in.)
23932-P21-000 0.63 mm (0.025 in.)
23933-P21-000 0.66 mm (0.026 in.)
23934-P21-000 0.69 mm (0.027 in.)
23935-P21-000 0.72 mm (0.028 in.)
72 mm Shim
F
G
H
B
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
AB
AC
AD
AE
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AP
AQ
AR
AS
AT
AV
AW
AX
AY
AZ
BA
BB
BC
BD
BE
Part Number Thickness
23936-P21-000 0.75 mm (0.030 in.)
23937-P21-000 0.78 mm (0.031 in.)
23938-P21-000 0.81 mm (0.032 in.)
23939-P21-000 0.84 mm (0.033 in.)
23940-P21-000 0.87 mm (0.034 in.)
23941-P21-000 0.90 mm (0.035 in.)
23942-P21-000 0.93 mm (0.037 in.)
23943-P21-000 0.96 mm (0.038 in.)
23944-P21-000 0.99 mm (0.039 in.)
23945-P21-000 1.02 mm (0.040 in.)
23946-P21-000 1.05 mm (0.041 in.)
23947-P21-000 1.08 mm (0.043 in.)
23948-P21-000 1.11 mm (0.044 in.)
23949-P21-000 1.14 mm (0.045 in.)
23950-P21-000 1.17 mm (0.046 in.)
23951-P21-000 1.20 mm (0.047 in.)
23952-P21-000 1.23 mm (0.048 in.)
23953-P21-000 1.26 mm (0.050 in.)
23954-P21-000 1.29 mm (0.051 in.)
23955-P21-000 1.32 mm (0.052 in.)
23956-P21-000 1.35 mm (0.053 in.)
23957-P21-000 1.38 mm (0.054 in.)
23958-P21-000 1.41 mm (0.056 in.)
23959-P21-000 1.44 mm (0.057 in.)
23960-P21-000 1.47 mm (0.058 in.)
23961-P21-000 1.50 mm (0.059 in.)
23962-P21-000 1.53 mm (0.060 in.)
23963-P21-000 1.56 mm (0.061 in.)
23964-P21-000 1.59 mm (0.063 in.)
23965-P21-000 1.62 mm (0.064 in.)
23966-P21-000 1.65 mm (0.065 in.)
23967-P21-000 1.68 mm (0.066 in.)
23968-P21-000 1.71 mm (0.067 in.)
23969-P21-000 1.74 mm (0.069 in.)
23970-P21-000 1.77 mm (0.070 in.)
23971-P21-000 1.80 mm (0.071 in.)
23972-PPP-J00 1.83 mm (0.072 in.)
23973-PPP-J00 1.86 mm (0.073 in.)
23974-PPP-J00 1.89 mm (0.074 in.)
23975-PPP-J00 1.92 mm (0.076 in.)
23976-PPP-J00 1.95 mm (0.077 in.)
23977-PPP-J00 1.98 mm (0.078 in.)
23978-PPP-J00 2.01 mm (0.079 in.)
23979-PPP-J00 2.04 mm (0.080 in.)
23980-PPP-J00 2.07 mm (0.081 in.)
23981-PPP-J00 2.10 mm (0.083 in.)
23982-PPP-J00 2.13 mm (0.084 in.)
23983-PPP-J00 2.16 mm (0.085 in.)
23984-PPP-J00 2.19 mm (0.086 in.)
23985-PPP-J00 2.22 mm (0.087 in.)
23986-PPP-J00 2.25 mm (0.089 in.)