Xerox WorkCentre 5687 Series Service Manual page 982

– Static eliminator on bin 0 entry, PL 11.118 Item 7.
– Static eliminator on the tamper assembly, PL 11.112 Item 5.
– Static eliminator on the bin 1 entry, PL 11.120 Item 7.
– Check that all of the connectors on the 1K LCSS PWB are pushed fully home.
Ensure that all of the ground wires are connected to the frame.
– Check all the harnesses for damage and short circuit to ground.
• 2K LCSS. Check the following:
– Ground connection on the power cord, PL 11.26.
– Static eliminator on bin 0 entry, PL 11.22 Item 7.
– Static eliminator on the tamper assembly, PL 11.16 Item 5.
– Static eliminator on the bin 1 entry, PL 11.23 Item 7.
– Check that all of the connectors on the LCSS PWB are pushed fully home. Ensure
that all of the ground wires are connect to the frame.
– Check all the harnesses for damage and short circuit to ground.
• HCSS. Check the following:
– Ground connection on the power cord, PL 11.56 Item 4.
– Static eliminator and static clip on the top cover, PL 11.32 Item 5.
– Static eliminator on the compiler carriage, PL 11.47 Item 10.
– Check the ground harnesses on transport motors 1A and 1B, PL 11.38 Item 12.
– Check that all of the connectors on the HCSS PWB and the carriage PWB are
pushed fully home. Ensure that all of the ground wires are connected to the frame.
– Check all the harnesses for damage and short circuit to ground.
• HCSS BM. Check the following:
– Ground connection on the power cord, PL 11.92 Item 4.
– Static eliminator and static clip on the lower exit cover, PL 11.62 Item 5.
– Exit brush on the BM right hand cover, PL 11.88 Item 16.
– Check the static eliminator on the BM front frame, PL 11.80 Item 17.
– Ground wire on the BM compiler motor, PL 11.86 Item 4.
– Ground wire on the BM back stop motor, PL 11.82 Item 1.
– Ground harnesses on transport motors 1A and 1B, PL 11.70 Item 12.
– Check that all of the connectors on the HCSS PWB, BM PWB and the carriage PWB
are pushed fully home. Ensure that all of the ground wires are connected to the
frame.
– Check all the harnesses for damage and short circuit to ground.
NOTE: The HVF may optionally have a tri folder and PPI unit. Where fitted, these should
also be checked.
• HVF. Check the following:
– Ground connection to the power supply unit, PL 11.157 Item 1.
– Static eliminator on BM entry. PL 11.161 Item 26.
– Exit brush on HVF top exit, PL 11.155.
– Static eliminator on BM exit, PL 11.168 Item 16.
– Exit brush on the Tri folder right hand frame, PL 11.190.
– Ground wire on the BM compiler motor, PL 11.166 Item 4.
Status Indicator RAPs
OF10
– Ground wire on the BM back stop motor, PL 11.163 Item 1.
– Ground wires to HVF entry and exit feed motors, PL 11.150.
– Ground wires to HVF buffer reed and bypass feed motors, PL 11.150.
– Ground wire to front of HVF paddle module, PL 11.145 Item 2.
– Ground wire to the HVF offset motor, PL 11.140 Item 19.
– Ground wire to HVF paper pusher motor, PL 11.145 Item 13.
– Ground wire to HVF staple assembly, PL 11.140 Item 14.
– Check that all of the connectors on the HVF PWB, and BM PWB are pushed fully
home. Ensure that all of the ground wires are connected to the frame.
– Where the Tri Folder PWB and the PPI options are installed check that the PWB
connectors are pushed fully home. Ensure that all of the ground wires are connected
to the frame
– Ground wire on the PPI PWB, PL 11.179.
– PPI docking PJ and connector.
– Check all the harnesses for damage and short circuit to ground.
August 2007
2-790 WorkCentre 5687 Family