Table of Contents
Advertisement
11-451-171 to 11-455-171 HVF Ejector Roll & Lower Paddle
RAP
11-451-171 The ejector roll motor has stalled.
11-452-171 The ejector roll did not return to the home position.
11-453-171 The ejector roll did not move from the home position.
11-454-171 The lower paddle has failed to return to the home position.
11-455-171 The lower paddle has failed to move from the home position.
Initial Actions
WARNING
Switch off the electricity to the machine, GP 14. Disconnect the power cord from the
customer supply while performing tasks that do not need electricity. Electricity can
cause death or injury. Moving parts can cause injury.
Check for any damage or obstructions that would prevent the ejector roll and lower paddle from
operating correctly.
Procedure
Figure 1, Figure 2 and Figure 3 show the component locations.
Enter dC330 code, 11-032 to take the bin 1 stacker tray down.
Enter dC330 code 11-053, staple unit 1 forward. This moves the ejector module to the out posi-
tion.
Enter dC330 code 11-179, ejector plate home sensor. Manually turn the ejector belts a few
centimetres. The display changes.
Y
N
Go to Flag 1. Check the wiring and repair as necessary, REP 1.2. Check the ejector plate
home sensor, Q11-179. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J401 HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Ejector plate home sensor, Q11-179, PL 11.140.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-178, ejector plater encoder sensor. Enter the code, 11-088 to rotate
the ejector roll motor one cycle of the ejector plates in the forward direction. The
changes.
Y
N
The ejector roll motor turned.
Y
N
Go to Flag 2. Check the wiring and repair as necessary, REP 1.2. Check the ejector
roll motor, MOT 11-088. Refer to:
•
GP 10 How to Check a Motor.
•
P/J801 on the HVF PWB.
A
B
WorkCentre 5687 Family
A
B
•
11A-171 HVF Power Distribution RAP.
Install new components as necessary:
•
Ejector roll motor, MOT 11-088, PL 11.140.
•
HVF control PWB, PL 11.157.
Go to Flag 3. Check the wiring and repair as necessary, REP 1.2. Check the ejector plate
encoder sensor, Q11-178. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J401 on the HVF control PWB.
•
11A-171 HVF Power Distribution RAP.
Install new components as necessary:
•
Ejector plate encoder sensor, Q11-178, PL 11.140.
•
HVF control PWB, PL 11.157 Item 2.
Measure the voltage at P/J401, pin B4. Figure 3, Rotate the lower paddle upwards and
inwards for one full rotation. The voltage changes from a logic high to a low, and then
back to high.
Y
N
Go to Flag 4. Check the wiring and repair as necessary, REP 1.2. Check the ejector lower
paddle switch, S11-180. Refer to:
•
GP 13 How to Check a Switch.
•
P/J401 HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Ejector lower paddle switch, Q11-180, PL 11.140.
•
HVF control PWB, PL 11.157 Item 2.
Measure the voltage at P/J401, pin B12. Actuate the ejector paper present sensor by placing a
sheet of paper on the ejector module. The voltage changes.
Y
N
Go to Flag 5. Check the wiring and repair as necessary, REP 1.2. Check the ejector paper
present sensor. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J401 HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Ejector paper present sensor, PL 11.140.
•
HVF control PWB, PL 11.157 Item 2.
display
Perform SCP 6 Final Actions.
August 2007
2-623
Status Indicator RAPs
11-451-171 to 11-455-171
Hide quick links:
Advertisement
Chapters
Table of Contents
