11-479-171 HVF PPI Paper Length Fault RAP
11-479-171 A shorter than expected sheet has been fed from the PPI, (Post Print Inserter).
Initial Actions
Check that the inserter paper path is clear of obstructions and the sensors are clean.
Procedure
WARNING
Switch off the electricity to the machine, GP 14. Disconnect the power cord from the
customer supply while performing tasks that do not need electricity. Electricity can
cause death or injury. Moving parts can cause injury.
Figure 1 shows the component locations.
Enter the dC330 code 11-150, inserter paper length 1 sensor. Operate the sensor using a
sheet of paper. The sensor display changes state.
Y
N
Go to Flag 1 and Flag 2 and check the inserter paper length 1 sensor, Q11-150. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J6, inserter control PWB.
•
P/J4, inserter control PWB.
•
P/J701, HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Inserter paper length 1 sensor, Q11-150, PL 11.175 Item 12.
•
Inserter control PWB, PL 11.179 Item 9.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-151, inserter paper length 2 sensor. Operate the sensor using a
sheet of paper. The sensor display changes state.
Y
N
Go to Flag 3 and Flag 4 and check the inserter paper length 2 sensor, Q11-151. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J6, inserter control PWB.
•
P/J4, inserter control PWB.
•
P/J701, HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Inserter paper length 2 sensor, Q11-151, PL 11.175 Item 12.
•
Inserter control PWB, PL 11.179 Item 9.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-155, inserter pick up sensor. Operate the sensor using a sheet of
paper. The sensor display changes state.
Y
N
Go to Flag 5 and Flag 6 and check the paper path, Q11-154. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J6, inserter control PWB.
A
Status Indicator RAPs
11-479-171
A
•
P/J4, inserter control PWB.
•
P/J701, HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Pickup sensor, Q11-154, PL 11.179 Item 11.
•
Inserter control PWB, PL 11.179 Item 9.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-154, inserter paper path sensor. Operate the sensor using a sheet of
paper. The sensor display changes state.
Y
N
Go to Flag 7 and Flag 8 and check the inserter paper path sensor, Q11-154. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J6, inserter control PWB.
•
P/J4, inserter control PWB.
•
P/J701, HVF control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Inserter paper path sensor Q11-154, PL 11.175 Item 10.
•
Inserter control PWB, PL 11.179 Item 9.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-077, to energize the inserter clutch. The inserter clutch is ener-
gised.
Y
N
Go to Flag 9 and Flag 10 and check the inserter clutch, CL11-077. Refer to:
•
GP 12 How to Check a Solenoid or Clutch.
•
P/J703, HVF control PWB.
•
P/J4, inserter control PWB.
•
P/J12, inserter control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Inserter clutch, CL077, PL 11.179 Item 3.
•
Inserter control PWB, PL 11.179 Item 9.
•
HVF control PWB, PL 11.157 Item 2.
Enter the dC330 code 11-078, to run the inserter motor. The inserter motor runs.
Y
N
Go to Flag 11 and Flag 12 and check the inserter motor, MOT11-078. Refer to:
•
GP 10 How to Check a Motor.
•
P/J701, HVF control PWB.
•
P/J4, inserter control PWB.
•
P/J12, inserter control PWB.
•
11A-171, HVF Power Distribution RAP.
Install new components as necessary:
•
Inserter motor, MOT078, PL 11.181 Item 1.
B
August 2007
2-640
WorkCentre 5687 Family