Xerox WorkCentre 5687 Series Service Manual page 968

Table 3 Status messages O to R
Status
UI Message Code Reason for Message
Please check the output bin 03-510 When paper is delivered to the
for blank and partially output and a video complete
imaged sheets and discard has not been received by the
them image processor
Please close the Booklet 11-921 The stapler position sensor
Maker Stapler module indicates the stapler module is
not closed in initialisation
Please delete the job. No 22-504 No tray configured for media
tray is configured with the
required paper size. Press
the Job Status button. Then
select the Delete Button.
Please wait, adjusting fuser 10-540 Fuser temperature control fail-
temperature ure.
Please wait, freeing mem- 19-502 Out of memory resources. Fault
ory 19-401, 19-402
Please wait. The system is 03-556 When fault codes 03-351 and
attempting to recover from 03-354 are raised
a fault
Please wait. The system 03-501 prtgeneralReset MIB object on
software and the network the network controller is set to a
controller are about to be value of powerCycleReset(4)
reset from a remote client.
The reset may take sev-
eral minutes. Any jobs cur-
rently being marked will be
cancelled
Please wait, your job will 19-506 Job delayed status
continue shortly. Do not
press the Start button again
Please wait... The system 22-501 Attempting print recovery. 22-
is attempting to recover 306, 22-307, 22-309
Status Indicator RAPs
OF4b
Reference / Action UI Message
Perform 03-423, 424, Power down failure. Power
433, 434, 821, 822, off cannot be completed.
831, 832 RAP Press the power button on
the left side of the machine.
If there is no response
Close the BM stapler
within 1 minute, then
module. If necessary,
remove the power cord.
perform 11-063-171,
Wait 1 minute then reinsert
11-411-171 RAP for
the power cord and switch
staple unit 1, and 11-
the machine on.
403-171, 11-413-171,
11-414-171 RAP for Printing and scanning are
staple unit 2 unavailable. Please call for
assistance
Configure one tray for
this stock size. Printing is unavailable
Pull out fuser module, then
firmly push it back in
Perform 10-322, 10-
Pull out xerographic mod-
324, 10-325, 10-330,
ule, then firmly push it back
10-370 RAP, 10-315,
in
10-320, 10-321, 10-
Punch Chad Bin Set State
323, 10-340, 10-350,
10-360, 10-380 RAP
Raise document handler
Perform 19-401, 19-
402, 19-403 RAP
Raise document handler
Perform 03-350, 03-
351, 03-354 RAP
Raise document handler
None
RARP functions are not
available. Please notify
machine administrator
Reload originals and press
start
High EPC usage. Per-
Reload originals and press
form 19-401, 19-402,
Start
19-403 RAP
Reload originals or select
Perform 22-306 to 22-
original size and press Start
315, 22-801, 814 RAP
Remove documents from
the paper tray and close
the cover
August 2007
2-776
Table 3 Status messages O to R
Status
Code Reason for Message Reference / Action
03-520 System fails to power off after Perform 03-374 RAP
request from the UI
03-500 Voltage not present on 24 V rail Perform 03-480 RAP
monitored by IOT
09-550 Photoreceptor erase lamp has Perform 09-350 RAP
failed. 09-350 fault
03-547 IOT-FRU: unable to read from Perform 03-371, 03-
FRU. Fault 03-371 is raised. 372 RAP
03-548 IOT-XRU: unable to read from Perform 03-371, 03-
XRU. Fault 03-372 is raised. 372 RAP
11-541 The chad bin has been Reinstall the chad bin
removed from the finisher
05-522 Sheet left over DADH CVT sen- Remove sheet
sor after jam
05-523 Sheet left over DADH registra- Remove sheet
tion sensor after jam
05-524 Sheet left over DADH exit sen- Remove sheet. Per-
sor after jam form 05-345, 05-346
RAP
16-594 Network controller - RARP Connectivity fix and
address resolution fails switch off the machine
then switch on the
machine, GP 14.
14-566 CCD (width) and length sen- Reposition originals
sors cannot determine size of and press start, Per-
the original form 14A RAP
05-503 Not enough originals during Reload originals
recovery
05-546 On pre-feed the DADH fails to Reload originals or
recognize the size of the docu- select size. Perform
ment 05C RAP
05-502 Document present in DADH Lower the document
tray with DADH cover open handler to scan your
documents. Perform
05-300 RAP
WorkCentre 5687 Family