Xerox WorkCentre 5687 Series Service Manual page 936

Table of Contents

Advertisement

Table 5 05-5XX Status codes
Status
Code
UI Message
Reason for Message
05-522 Raise document handler
Sheet left over DADH CVT
sensor after jam
05-523 Raise document handler
Sheet left over DADH registra-
tion sensor after jam
05-524 Raise document handler
Sheet left over DADH exit sen-
sor after jam
05-525 Remove all documents
Sheet left over DADH docu-
from the document han-
ment present sensor after jam
dler tray
05-526 Open document handler
DADH - sheet near CVT sen-
top cover
sor in duplex path. 05-352 fault
is raised
05-530 No message
Document in DADH tray
05-531 No message
Document in DADH area 2
with no document in area 3
05-532 No message
Document in DADH area 2
with document in area 3
05-533 No message
Document in DADH area 3
05-534 Check for a stray original
Unscheduled document
in the document tray
detected by any sensor
05-535 Document is too short to
Open DADH cover
be scanned by the docu-
ment handler, use the doc-
ument glass
05-536 Close document handler
Open document handler
05-537 No message
DADH tray empty
05-538 Document handler is
DADH not available. 03-322,
unavailable
03-323 or 03-324 raised
Status Indicator RAPs
OF4a
Status
Reference / Action
Code
UI Message
Remove sheet. Perform
05-539 Document handler feed
05-350, 05-352 RAP
roll has been replaced
Remove sheet. Perform
05-340 RAP
05-540 Resort and reload all origi-
Remove sheet. Perform
nals.
05-345, 05-346 RAP
Remove sheet. Perform
05B RAP
05-542 Document Handler is
Reset when DADH top
unavailable
cover closed after jam
05-544 Resort and reload ALL the
cleared. Perform 05-
originals
350, 05-352 RAP
Remove document
from tray. Perform 05B
RAP
05-546 Reload originals or select
Remove document.
original size and press
Perform 05-330, 05-
Start
331, 05-335, 05-340
05-547 Re-order but do not
RAPs.
replace Document Han-
Remove document.
dler Feed Roll
Perform RAP. Perform
05-548 Please follow the instruc-
05-330, 05-331, 05-
tions below to replace the
335, 05-340 RAPs.
document handler feed
Remove document.
roll:
Perform RAP. Perform
05-560 Document is too short to
05-330, 05-331, 05-
be scanned by the docu-
335, 05-340 RAPs.
ment handler, use the doc-
Clear the document
ument glass
path in the DADH. Per-
05-586 Try turning the machine off
form 05-330, 05-331,
and on. Please call for
05-335, 05-340, 05-
assistance if the problem
345, 05-346 RAPs.
persists
Close document han-
dler cover. Perform 05-
05-588 Try turning the machine off
310 RAP
and on. Please call for
assistance if the problem
Close document han-
persists
dler. Perform 05-300
RAP
Put document in tray.
Perform 05B RAP
Perform 03-320, 03-
322 to 03-324 RAP and
14-320 RAP
August 2007
2-744
Table 5 05-5XX Status codes
Reason for Message
Reference / Action
DADH feed head CRU
None
replaced. Message automati-
cally cleared half a second
after setting
DADH document jam is
Replace document on
cleared for a single job
DADH input tray to
enable recovery. Check
for blanks in output tray.
Resume or cancel job
DADH document transport
Perform 05A RAP
needs service
Document jam is cleared (cov-
Resume job command
ers cycled and switch cleared)
is given with documents
and 'normal job' or 'build job'
replaced in input tray, if
required, or cancel job
command is given
On pre-feed the DADH fails to
Reload originals or
recognize the size of the docu-
select size. Perform
ment
05C RAP
DADH feed roll assembly near
Re-order feed roll
end of life
assembly PL 5.15 Item
1.
DADH feed roll assembly at
Install a new feed roll
end of life
assembly, PL 5.15 Item
1.
Document too short for DADH,
Remove document
use document glass. Fault 05-
from DADH during jam
310 raised
clearance, Perform 05-
310 RAP
Network controller software
Perform 03-340, 03-
version supplied at power-on is
416 RAP. If necessary,
not compatible with image pro-
reload the software, GP
cessor PWB. Fault 03-416 is
4
raised
Finisher software version sup-
Perform 03-360, 03-
plied is not compatible. Fault
408 to 03-410, 03-418
03-418 raised
RAP If necessary,
reload the software, GP
4
WorkCentre 5687 Family

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wc5632fWc5545fWc5675fWc5645fWc5687fWc5655f

Table of Contents