B-130 Hcss Initialization Failure Rap - Xerox WorkCentre 5687 Series Service Manual

11B-130 HCSS Initialization Failure RAP

There are four different initialization sequences which depend on the machine state when an
initialize command is sent.
1. Initialize (purge) - If there was no previous mechanical fault, the paper path motors run
and the ejector housing is cycled open and closed.
2. Initialize (purge) - If there was a previous mechanical fault, a full mechanical initialization
is carried out, as listed below.
3. Initialize (retain) - This is the sequence to recover from a paper jam. The paper path
motors are run and the output bin height is adjusted.
4. Initialize (check) - This is the normal power on sequence. This sequence does not per-
form any mechanical initialization. Only the paper path sensors, bin full sensors and the
interlocks are checked.
When an initialization command is received from the machine, the units are initialized in two
stages:
• The following units are initialized sequentially:
1. If the staple head is not at the home position, it is driven to the home position.
2. If the stapling unit is not at the home position, it is driven to the home position.
3. If the compiler ejector is not at the home position, it is driven to the home position.
• The following units are then initialized simultaneously:
– If the front tamper is not at the home position, it is driven to the home position.
– If the rear tamper is not at the home position, it is driven to the home position.
– If the compiler carriage is not at the home position, it is driven to the home position.
– If the paddle is not at the home position, it is driven to the home position.
– If bin 1 is not at the home position, it is driven to the home position.
– If bin 1 is not at the offset home position, it is driven to the offset home position.
– If bin 2 is not at the home position, it is driven to the home position.
– If bin 2 is not at the offset home position, it is driven to the offset home position.
– If the hole punch is not at the home position, it is driven to the home position.
NOTE: The staple cartridge must be fully pushed home.
Initial Actions
Open the HCSS front door, so that the compiler carriage can be viewed. Cheat the front door
interlock switch.
Procedure
If the initialization sequence fails to place any unit at the home position, refer to the appropriate
RAPs:
• If all modules of the HCSS fail to initialize, refer to 11-300-130, 11-303-130, 11-304-130,
11-305-130 Interlocks RAP and check the upper and lower exit gate interlocks.
• Front tamper not at the home position, refer to 11-005-130, 11-006-130, 11-310-130, 11-
311-130 Front Tamper Move Failure RAP.
• Rear tamper not at the home position, refer to 11-007-130, 11-008-130, 11-312-130, 11-
313-130 Rear Tamper Move Failure RAP.
• Compiler carriage not at the home position, refer to 11-012-130, 11-014-130, 11-315-130,
11-316-130 Compiler Carriage Position Failure RAP.
Status Indicator RAPs
11B-130
• Paddle not at the home position, refer to 11-024-130, 11-025-130 Paddle Position Failure
RAP.
• Bin 1 not at the home position, refer to 11-030-130, 11-336-130 Bin 1 Movement Failure
RAP.
• Bin 1 not at the offset home position, refer to 11-031-130, 11-337-130 Bin 1 Offset Failure
RAP.
• Bin 2 not at the home position, refer to 11-036-130, 11-346-130 Bin 2 Movement Failure
RAP.
• Bin 2 not at the offset home position, refer to 11-040-130, 11-347-130 Bin 2 Offset Failure
RAP.
• Hole punch not at the home position, refer to 11-043-130 Hole Punch Cycle Failure RAP.
• Staple head not at the home position, refer to 11-050-130, 11-360-130 Staple Head Oper-
ation Failure RAP.
• Stapling unit not at the home position, refer to 11-053-130, 11-370-130 Stapling Unit
Movement Failure RAP.
• Compiler ejector not at the home position, refer to 11-320-130, 11-322-130 Compiler Ejec-
tor Movement Failure RAP.
August 2007
2-438 WorkCentre 5687 Family