Xerox WorkCentre 5687 Series Service Manual page 938

Table 7 07-5XX Status codes
Status
Code UI Message Reason for Message
07-541 Tray 1 is out of service, Tray 1 out of service.
please use a different tray
07-542 Tray 2 is out of service, Tray 2 out of service.
please use a different tray
07-543 Tray 3 is out of service, Tray 3 elevate top sensor does
please use a different tray not turn on within 7 seconds
after elevator motor on.
07-544 Tray 4 is out of service, Tray 4 elevate top sensor does
please use a different tray not turn on within 7 seconds
after elevator motor on
07-546 Tray 5 is out of service, Tray 5 cannot feed paper
please use a different tray
07-550 Tray 3 is lifting Tray 3 is lifting.
07-560 Tray 4 is lifting Tray 4 is lifting
07-561 Tray 5 is lifting, please Tray 5 is currently lifting
wait
07-562 - Tray 5 is currently lowering
07-563 Tray 5 is unavailable. Tray 5 lifting has stopped
Check for obstructions in
Tray 5
07-564 Tray 5 is unavailable. Tray 5 lowering has stopped
Check for obstructions in
Tray 5
07-571 Paper size mismatch. First sheet fed after a tray 1
Check paper in Tray 1. status change does not match
Some image loss may the confirmed stock
occur
07-572 Paper size mismatch. First sheet fed after a tray 2
Check paper in Tray 2. status change does not match
Some image loss may the confirmed stock
occur
07-573 Paper size mismatch. First sheet fed after a tray 3
Check paper in Tray 3. status change does not match
Some image loss may the confirmed stock
occur
07-574 Paper size mismatch. First sheet fed after a tray 4
Check paper in Tray 4. status change does not match
Some image loss may the confirmed stock
occur
Status Indicator RAPs
OF4a
Status
Reference / Action Code UI Message
Perform 07F RAP 07-575 Paper size mismatch.
Check paper in Bypass
tray. Some image loss
Perform 07F RAP
may occur
07-576 Paper size mismatch.
Perform 07-355 RAP
Check paper in tray 5
07-580 Reorder but do not
Perform 07-360 RAP
replace the Tray 5 Feed
Rolls
07-581 Slide Tray 5 up to
Switch the machine off
machine
and on, GP 14. Check
that the tray is in the 07-590 <Replace tray 5 feed rolls
correct position. Per- message>
form 07-306, 07-372, or
07-373 RAP
Perform 07-355 RAP
Perform 07-360 RAP
Perform 07-373 Status
Code UI Message
Perform 07-374
08-549 Clear jam from right hand
Perform 07-373 side of Tray 5
08-550 Open left hand door
Perform 07-374
08-551 Open left hand door
Check the paper in tray
1. Perform 07D RAP
08-552 Open left hand door
Check the paper in tray
08-553 Open tray 3
2. Perform 07D RAP
08-554 Open left hand door
Check the paper in tray
3. Check that the tray is
set to correct paper
08-555 Open front door
size, ADJ 7.1
Check the paper in tray
4. Check that the tray is
08-556 Open front door
set to correct paper
size, ADJ 7.1
August 2007
2-746
Table 7 07-5XX Status codes
Reason for Message Reference / Action
First sheet fed after a bypass Check the paper in
tray status change does not bypass tray and the
match the confirmed stock side guide is set cor-
rectly
The first sheet after a tray 5 Confirm the paper size
status change does not match in the UI
the confirmed stock
Near the end of life - ensure Order new feed roll kit,
new stock is available PL 8.45 Item 2
Tray 5 is un-docked Perform 07-372
The feed head counter has Install new tray 5 feed
reached the end of life figure rolls, PL 8.45 Item 2
Table 8 08-5XX Status codes
Reason for Message Reference / Action
Sheet did not clear the wait Perform 08-115B, 08-
sensor within the expected 117B
time
Sheet over wait sensor Jam clearance. Per-
form 08-100A RAP
Tray 1 feed sensor detects Jam clearance. Per-
paper in feed area on power- form 08-101 RAP
on or in standby, 08-101
Tray 2 feed sensor detects Jam clearance. Per-
paper in feed area on power- form 08-102 RAP
on or in standby. 08-102
Tray 3 feed sensor detects Jam clearance. Per-
paper in feed area on power- form 08-103, 08-113
on or in standby. 08-103 RAP
Tray 4 feed sensor detects Jam clearance. Per-
paper in feed area on power- form 08-104, 08-114
on or in standby. 08-104 RAP
Registration sensor detects Jam clearance. Per-
paper in registration area on form 08-150A, 08-
power-on or in standby. 08-150 151A RAP
Paper in duplex path at power- Jam clearance. Per-
on or in standby form 08-160A, 08-
161A RAP
WorkCentre 5687 Family