Paper Exiting To Bin 0 Rap - Xerox WorkCentre 5687 Series Service Manual

11-130-120, 11-132-120 Paper Exiting to Bin 0 RAP

11-130-120 The leading edge of the sheet is late to the top exit sensor.
11-132-120 The trailing edge of the sheet is late from the top exit sensor.
Initial Actions
Check the following:
• 1K LCSS PWB DIP switch settings, refer to 11E-120 1K LCSS PWB DIP Switch Settings
RAP.
• Ensure the paper tray guides are set to the correct position for the size of paper in the
tray.
• The tensioner on the intermediate paper drive belt. Check that the tensioner is free to
move and that the tensioner pulley is free to rotate. If necessary lubricate the tensioner
and tensioner pulley, REP 11.3-120. Refer to GP 18 Machine Lubrication.
NOTE: The tensioner arm and the tensioner pulley require different lubricants, refer to
REP 11.3-120.
• That the drive pulleys on both transport motor 1 and 2 are secure and do not slip on the
motor shaft.
• All the transport drive belts are correctly fitted and are in a good condition
• All the transport rolls and idler pulleys are free to rotate.
• The diverter gate and linkage for free movement.
• A paper jam in the path to bin 0.
• Paper fragments from a previous jam clearance action.
• A paper jam in the path to the top tray. If the jams occur shortly after install. Check the gap
between the entry guide cover, PL 11.122 Item 5 and the paper guide PL 11.118 Item 10.
If the gap is less than 1 mm, adjust or install a new entry guide cover. Refer to the
replacement procedure in REP 11.13-120.
Refer to the 11G-120 Copy Damage in the 1K LCSS RAP and the 11H-120 Mis-Registration in
Stapled Sets and Non-Stapled Sets RAP.
NOTE: Paper is diverted to bin 0 when the diverter gate solenoid is energized. Paper is fed to
bin 1 when the diverter gate solenoid is de-energized.
Procedure
NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors.
NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state
on the UI. Make sure that the correct sensor or switch is tested.
Enter dC330, code 11-001 transport motor 2, MOT11-001, Figure 1. MOT11-001 runs.
Y N
Go to Flag 3. Check MOT11-001.
Refer to:
• 11F-120 1K LCSS PWB Damage RAP.
• GP 10, How to Check a Motor.
• P/J16, 1K LCSS PWB.
• 11C-120 1K LCSS Power Distribution RAP.
A
Status Indicator RAPs
11-130-120, 11-132-120
A
Repair or install new components as necessary:
• Transport motor 2, PL 11.120 Item 13.
• 1K LCSS PWB, PL 11.124 Item 1.
NOTE: The diverter gate solenoid remains energized for 5 seconds.
Enter dC330, code 11-002 diverter gate solenoid, SOL11-002. SOL11-002 energizes.
Y N
Go to Flag 2. Check SOL11-002.
Refer to:
• 11F-120 1K LCSS PWB Damage RAP.
• GP 12, How to Check a Solenoid.
• P/J13, 1K LCSS PWB
• 11C-120 1K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Diverter gate solenoid, PL 11.118 Item 12.
• 1K LCSS PWB, PL 11.124 Item 1.
Enter dC330, code 11-130, top exit sensor, Q11-130. Actuate Q11-130. The
changes.
Y N
Go to Flag 1. Check Q11-130.
Refer to:
• 11F-120 1K LCSS PWB Damage RAP.
• GP 11, How to Check a Sensor.
• P/J2, 1K LCSS PWB
• 11C-120 1K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Top exit sensor, PL 11.118 Item 11.
• 1K LCSS PWB, PL 11.124 Item 1.
Enter dC330, code 11-000, transport motor 1, MOT11-000. MOT11-000 runs.
Y N
Go to Flag 4. Check MOT11-000.
Refer to:
• 11F-120 1K LCSS PWB Damage RAP.
• GP 10, How to Check a Motor.
• P/J17, 1K LCSS PWB.
• 11C-120 1K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Transport motor 1, PL 11.110 Item 2.
• 1K LCSS PWB, PL 11.124 Item 1.
Perform SCP 6 Final Actions.
August 2007
2-350
display
WorkCentre 5687 Family