Table of Contents
Advertisement
11K-171 HVF Initialization Failure RAP
When an initialization command is received from the machine, the HVF is initialized with the
following actions:
1.
The tray lowers.
2.
The flapper performs two revolutions.
3.
The ejector module travels to the out position.
4.
The stapler unit travels to the inboard position.
5.
The stapler unit returns to the outboard position.
6.
The ejector module returns to the home position.
7.
The tray offsets.
8.
The three feed motors start.
9.
The booklet maker diverter solenoid actuates, if applicable.
10. The exit diverter solenoid actuates.
11. The booklet maker diverter solenoid de-actuates.
12. The exit diverter solenoid de-actuates.
13. The three feed motors stop.
14. The hole punch operates, if applicable.
15. The tray returns to the home position.
NOTE: The HVF initialization procedure can be triggered by opening and closing the HVF front
door, or by raising and lowering the top tray. When this is done the tray will not lower com-
pletely, but will adjust its position.
The booklet maker is initialized as follows:
1.
The BM tampers are driven to their home position, unless already home.
2.
The BM backstop is driven to the home position, unless already home
3.
The BM crease roll gate is driven to the home position, unless already home
4.
The BM crease blade is driven to the home position, unless already home
5.
The BM staple heads are driven to their home position, unless already home.
Initial Actions
WARNING
Switch off the electricity to the machine, GP 14. Disconnect the power cord from the
customer supply while performing tasks that do not need electricity. Electricity can
cause death or injury. Moving parts can cause injury.
Open the HVF front door. Cheat the front door interlock switch. Fully pull out the BM module
Procedure
If the initialization sequence fails to place any unit at the home position, refer to the appropriate
RAPs:
•
Front tamper not at home, refer to 11-392-171 to 11-395-171 HVF Front tamper Tray RAP
•
Rear tamper not at home, refer to 11-396-171 to 11-399-171 HVF Rear Tamper Tray RAP.
•
Paddle not at home, refer to 11-024-171, 11-026-171 Paddle Roll Position RAP.
•
Bin 1 not at home, refer to 11-460-171 to 11-462-171 HVF Bin 1 Position RAP.
•
Punch not at home, refer to 11-044-171 to 11-047-171 Punch head Position RAP
WorkCentre 5687 Family
•
Staple head not at home, refer to 11-371-171 to 11-377-171 HVF stapler Position and
Priming RAP.
•
Ejector not at home, refer to 11-450-171, 11-456-171 to 11-459-171 HVF Ejector Module
RAP.
•
The buffer motor fails to start, refer to 11-164-171, 11-165-171 HVF Buffer Path RAP.
•
Entry feed motor 1 fails to start, refer to 11-100-171, 11-101-171 HVF Entry Sensor RAP.
•
Exit feed motor 2 fails to start, refer to 11-130-171, 11-132-171 HVF Top Exit Sensor RAP.
•
The tray fails to offset, refer to 11-173-171 to 11-177-171 HVF Offset Unit RAP.
•
The booklet maker diverter solenoid fails to operate, refer to 11-158-171, 11-160-171,
162, 163-171
•
The exit diverter solenoid fails to operate, refer to 11-130-171, 11-132-171 HVF Top Exit
Sensor RAP.
•
Either of the BM staple heads are not at the home position, refer to 11-063-171, 11-411-
171 HVF BM Stapler Unit 1 Failure RAP or 11-403-171, 11-413-171, 11-414-171 HVF BM
Stapler Head 2 and Stapler Module RAP.
•
The BM tampers are not at the home position, refer to 11-066-171, 11-384-171 HVF BM
Tamper Failure RAP.
•
The BM backstop is not at the home position, refer to 11-065-171, 11-383-171 HVF BM
Backstop Failure RAP.
•
The BM crease roll gate is not at the home position, refer to 11-415-171 HVF BM Crease
Roll Gate Home RAP.
•
The BM crease blade is not at the home position, refer to 11-061-171, 11-416-171 HVF
BM Creasing RAP.
August 2007
2-661
Status Indicator RAPs
Hide quick links:
Advertisement
Chapters
Table of Contents
