Xerox WorkCentre 5687 Series Service Manual page 969

Table 3 Status messages O to R
Status
UI Message Code Reason for Message
Remove all documents 05-525 Sheet left over DADH docu-
from the document handler ment present sensor after jam
tray
Remove misfed sheet. 07-521 IOT microprocessor detects
Close tray 1 Tray 1 open
Remove misfed sheet. 07-522 IOT microprocessor detects
Close tray 2 Tray 2 open
Remove misfed sheet. 07-523 IOT microprocessor detects
Close tray 3 Tray 3 open
Remove misfed sheet. 07-524 IOT microprocessor detects
Close tray 4 Tray 4 open
Remove Reorder Toner 02-560 Set by the user interface when
Cartridge the user enters *33 code to
remove the Reorder Notifica-
tion message when the Toner
Cartridge is replaced.
Re-order but do not replace 05-547 DADH feed head near end of
Document Handler Feed life
Roll
Re-order but do not replace 10-521 Fuser counter reaches 290 k
fuser module prints
Re-order, but do not 09-584 Xerographic module near end
replace xerographic mod- of life
ule
Replace fuser module 10-520 Fuser counter reaches 300 k
prints
Replace fuser module 10-523 IOT detects fuser failure
Replace fuser module 10-570 FRU CRUM authorization fail-
ure. When fault 10-399 raised
Replace punch head unit 11-540 Punch head present sensor not
made
Replace staple cartridge 11-546 Staple cartridge empty
WorkCentre 5687 Family
Reference / Action UI Message
Remove sheet. Per- Restoring configuration set-
form 05B RAP ting. Please wait. System
will reboot when com-
pleted.
Close tray. Perform
07-301RAP
Toner cartridge empty
Close tray. Perform
07-302 RAP ROS laser not being con-
trolled
Close Tray. Perform
07-303 RAP ROS system failure. Print-
ing is unavailable. If fault
Close Tray. Perform
persists, call for assistance.
07-304 RAP
Touch Ignore Error to use
Cleared by the user
other services
interface once Status
09-599 is cleared.
Replace feed head or
end of life status
UI Message
Order a new fuser
Scan to file unavailable
module, PL 10.10
Item 1, PL 10.8 Item
1.
Re-order a new xero-
Scanner fault. Please call
graphic module
for assistance
Install new fuser mod-
Scanner has failed to initai-
ule, PL 10.10 Item 1,
ilize. Switch off the
PL 10.8 Item 1.
machine, wait 1 minute,
Install new fuser mod-
then switch on the
ule, PL 10.10 Item 1,
machine. If fault persists
PL 10.8 Item 1.
call for assistance, or press
Perform 10-399 RAP
close to use other services
Scanner is calibrating,
Perform 11-043-110,
please wait
11-350-110 RAP for
LCSS, 11-043-170,
11-350-170 RAP for
HCSS BM
Perform 11-364-110
RAP for LCSS, 11-
364-170, 11-370-170
RAP for HCSS BM
August 2007
2-777
Table 3 Status messages O to R
Status
Code Reason for Message Reference / Action
03-526 Software upgrade configura- When the Image proc-
tion reset cessing module has
completed restoring
the configuration set-
tings
09-592 Toner level sensor registers Install new toner car-
developer sump not full tridge, PL 9.15 Item 4.
06-540 ROS laser not being controlled. Perform 06-350 RAP
06-530 ROS system failed. Perform 06-340 RAP
Table 4 Status messages S to W
Status
Code Reason for Message Reference / Action
03-585 Fault 03-331 raised Cleared when status
03-544 is raised. Per-
form 03-340, 03-416
RAP
03-543 Image processing-CCD: three Perform 14-310 RAP
times retry fail at 100 ms cycle
communication - no response
14-563 Scanner needs service Switch off the
machine then switch
on the machine, GP
14. Perform 14-110
RAP, 14-310, 14-710
RAP, 14-720 RAP
14-560 Scanner is calibrating If calibration does not
complete, switch off
the machine, then
switch on the
machine, GP 14. Wait
for a few minutes, if
the scanner contin-
ues to calibrate with-
out completing
perform 14-703 to 14-
706, 712, 714, 716,
718 RAP
Status Indicator RAPs
OF4b