Xerox WorkCentre 5687 Series Service Manual page 937

Table 5 05-5XX Status codes
Status
Code UI Message Reason for Message
05-589 Try turning the machine off IOT, DADH or UI software ver-
and on. Please call for sion supplied at power-on is
assistance if the problem not compatible with the image
persists processor PWB
Table 6 06-5XX Status codes
Status
Code UI Message Reason for Message
06-520 The ROS motor has fail- ROS motor failed.
ure. Switch the machine
off, wait 1 minute, then
switch on the machine
again. If the fault persists
call for assistance or
press Close to use other
services.
06-530 ROS system failure. Print- ROS system failed.
ing is unavailable. If fault
persists, call for assis-
tance. Touch Ignore Error
to use other services
06-540 ROS laser not being con- ROS laser not being con-
trolled trolled.
Table 7 07-5XX Status codes
Status
Code UI Message Reason for Message
07-501 Check the settings for Tray 1 closed or size change
Tray 1 from power-on
07-502 Check the settings for Tray 2 closed or size change
Tray 2 from power-on
07-505 Check settings for the Bypass tray size confirmation
bypass tray required
07-506 Adjust position of Tray 1 Tray 1 guides moved out of
before proceeding 'fixed' position
07-507 Adjust position of Tray 2 Tray 2 guides moved out of
before proceeding 'fixed' position
WorkCentre 5687 Family
Status
Reference / Action Code UI Message
Perform 03-300, 306, 07-511 Tray 1 empty, please
461, 482, 805, 870 reload
RAP, 03-320, 03-322 to
07-512 Tray 2 empty, please
03-324 RAP, 03-310
reload
RAP. If necessary,
07-513 Tray 3 empty, please
reload the software, GP
reload
4
07-514 Tray 4 empty, please
reload
07-515 Bypass Tray empty,
please reload
Reference / Action
07-516 Tray 5 empty, please
Perform 06-020 RAP reload
07-517 Inserter empty, please
reload
07-521 Remove misfed sheet.
Close tray 1
07-522 Remove misfed sheet.
Close tray 2
Perform 06-340 RAP
07-523 Remove misfed sheet.
Close tray 3
07-524 Remove misfed sheet.
Close tray 4
07-526 Close tray 5 door
Perform 06-350 RAP
07-531 Tray 1 is low on paper
07-532 Tray 2 is low on paper
07-533 Tray 3 is low on paper
Reference / Action
07-534 Tray 4 is low on paper
Confirm the attributes
or open the tray
Confirm the attributes
or open the tray
07-536 Tray 5 is low on paper
Confirm the attributes
Open tray 1 and reset
07-539 Tray 5 is overloaded,
the paper guides
please remove excess
Open tray 2 and reset paper
the paper guides
August 2007
2-745
Table 7 07-5XX Status codes
Reason for Message Reference / Action
Tray 1 paper present sensor Reload paper. If neces-
detects no paper in tray sary perform 07A RAP
Tray 2 paper present sensor Reload paper. If neces-
detects no paper in tray sary perform 07A RAP
Tray 3 paper present sensor Reload paper. If neces-
detects no paper in tray sary perform 07A RAP
Tray 4 paper present sensor Reload paper. If neces-
detects no paper in tray sary perform 07A RAP
Paper present sensor detects Reload paper. If neces-
no paper in bypass tray, while sary perform 07A RAP
attempting to feed from the
bypass
Tray empty sensor detects no Reload paper. If neces-
paper sary, perform 07G
Paper sensor detects no paper Reload paper.
IOT microprocessor detects Close tray. Perform 07-
Tray 1 open 301RAP
IOT microprocessor detects Close tray. Perform 07-
Tray 2 open 302 RAP
IOT microprocessor detects Close Tray. Perform 07-
Tray 3 open 303 RAP
IOT microprocessor detects Close Tray. Perform 07-
Tray 4 open 304 RAP
Tray 5 door has been detected Close the door, or per-
open form 07-306
Tray 1 paper low Perform 07A RAP
Tray 2 paper low Perform 07A RAP
Tray 3 paper low IOT microprocessor
detects Tray 3 paper
level at 25%. Perform
07B RAP
Tray 4 paper low IOT microprocessor
detects Tray 4 paper
level at 25%. Perform
07B RAP
Tray 5 paper below 5% full Add paper. If neces-
sary, perform 07-373
and 07-374 RAPs
Paper equals or is more than Remove some paper. If
100% full in tray 5 necessary, perform 07-
373 and 07-374
Status Indicator RAPs
OF4a