Paper Exiting To Bin 0 Rap - Xerox WorkCentre 5687 Series Service Manual

11-130-110, 11-132-110 Paper Exiting to Bin 0 RAP

11-130-110 The leading edge of the sheet is late to the top exit sensor.
11-132-110 The trailing edge of the sheet is late from the top exit sensor.
WARNING
Take care not to topple the LCSS.
The LCSS is unstable when un-docked from the machine.
Do not show the customer how to un-dock the LCSS.
Initial Actions
Check the following:
• 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings
RAP.
• Ensure the paper tray guides are set to the correct position for the size of paper in the
tray.
• The tensioner on the intermediate paper drive belt. Check that the tensioner is free to
move and that the tensioner pulley is free to rotate. If necessary lubricate the tensioner
and tensioner pulley, REP 11.3-110. Refer to GP 18 Machine Lubrication.
NOTE: The tensioner arm and the tensioner pulley require different lubricants, refer to
REP 11.3-110.
• The drive pulleys on both transport motor 1 and 2 are secure and do not slip on the motor
shaft.
• All the transport drive belts are correctly fitted and are in a good condition
• All he transport rolls and idler pulleys are free to rotate.
• The diverter gate and linkage for free movement.
• A paper jam in the path to bin 0.
• Torn paper fragments from a previous jam clearance action.
• A paper jam in the path to the top tray. If the jams occur shortly after install. Check the gap
between the entry guide cover, PL 11.24 Item 5 and the paper guide PL 11.22 Item 10. If
the gap is less than 1 mm, adjust or install a new entry guide cover. Refer to the replace-
ment procedure in REP 11.15-110.
Refer to the 11H-110 Copy Damage in the 2K LCSS RAP and the 11J-110 Mis-Registration in
Stapled Sets and Non-Stapled Sets RAP.
NOTE: Paper is diverted to bin 0 when the diverter gate solenoid is energized.
Paper is fed to bin 1 when the diverter gate solenoid is de-energized.
Procedure
NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors.
NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state
on the UI. Make sure that the correct sensor or switch is tested.
Enter dC330, code 11-001 to run transport motor 2, MOT11-001, Figure 1. The motor runs.
Y N
Go to Flag 3 and check MOT11-001.
A
Status Indicator RAPs
11-130-110, 11-132-110
A
Refer to:
• 11G-110 2K LCSS PWB Damage RAP.
• GP 10, How to Check a Motor.
• P/J309, 2K LCSS PWB.
• 11D-110 2K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Transport motor 2, PL 11.22 Item 5.
• 2K LCSS PWB, PL 11.26 Item 1.
Enter dC330, code 11-002 to energize the diverter gate solenoid, S11-002, Figure 1. The
diverter gate solenoid energizes.
Y N
Go to Flag 2 and check SOL11-002.
Refer to:
• 11G-110 2K LCSS PWB Damage RAP.
• GP 12, How to Check a Solenoid.
• P/J306, 2K LCSS PWB.
• 11D-110 2K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Diverter gate solenoid, PL 11.22 Item 12.
• 2K LCSS PWB, PL 11.26 Item 1.
Enter dC330, code 11-130, actuate the top exit sensor, Q11-130, Figure 1. The
changes.
Y N
Go to Flag 1 and check Q11-130.
Refer to:
• 11G-110 2K LCSS PWB Damage RAP.
• GP 11, How to Check a Sensor.
• P/J313, 2K LCSS PWB.
• 11D-110 2K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Top exit sensor, PL 11.22 Item 11.
• 2K LCSS PWB, PL 11.26 Item 1.
Enter dC330, code 11-000 to energize the transport motor 1, MOT 11-000, Figure 1. The
motor energizes.
Y N
Go to Flag 4 and check MOT 11-000.
Refer to:
• 11G-110 2K LCSS PWB Damage RAP.
• GP 10, How to Check a Motor.
• P/J305, 2K LCSS PWB.
• 11D-110 2K LCSS Power Distribution RAP.
Repair or install new components as necessary:
• Transport motor 1, PL 11.14 Item 2.
B
August 2007
2-308
display
WorkCentre 5687 Family