Xerox WorkCentre 5687 Series Service Manual page 892

Network Controller Boot sequence
Connect the PWS to the network controller, using the Ethernet cable, GP 4 Network Controller
AltBoot S/w Download. Switch the machine off and on, GP 14. Select the AltBoot window on
the PWS and monitor the Network controller boot sequence.
NOTE: References to the ESS and the network controller, are to the same item.
Xerox User Flash Firmware
================================
ALTERNATE BOOT Ver 4.0
================================
_________________________________________________________________________
• System ID => e.g. Xerox Denali v1.00
• BIOS ID => e.g. American Megatreats Inc. 0701 03/04/2004
• Board ID => Celestica Denali P 2 CMY123432000378
• uP ID => AMD mobile and Duron (tm) 00800 MHz
• Main Revision +> e.g. 4.1.0
Explanation
• The System BIOS hands off boot up control.
NOTE: The network controller PWB BIOS displays the menu shown.
Critical Checks
• If this menu is not displayed and no beeps are heard, suspect a defective network control-
ler PWB or CPU not seated correctly.
• If this menu is not displayed and two beeps are heard, approximately 30 sec. after power
on, check the following, GP 7:
– a defective connection between the network controller PWB, PL 16.10 Item 1 and
the network controller disk drive, PL 16.10 Item 5.
– a defective network controller disk drive, PL 16.10 Item 5.
• If this menu is not displayed and three beeps are heard repeatedly, suspect a loose,
defective or missing network controller memory. Check the memory module connections.
_________________________________________________________________________
Press Any Key For AltBoot Menu (05):..... (04)...... (03):......:(02):...... (01):...... (00):
_________________________________________________________________________
Explanation
• The BIOS displays this interrupt message. Pressing any key within 9 seconds will display
the Altboot Options menu.
NOTE: The Altboot Options menu is used when loading network controller software using
the Alternate Boot method.
• A single audible beep will be heard when the interrupt time expires.
Status Indicator RAPs
16A
• The BIOS then probes the bus for the network controller HDD.
Critical Checks
• If the boot sequence stops at the interrupt statement, suspect no software image on the
network controller HDD, no power to the network controller HDD, a bad connection from
the network controller HDD to the cable or a defective network controller HDD, PL 16.10
Item 5.
• If the start button appears to be locked up, the machine reboots / resets and the network
controller will not boot up. Remove and reconnect the HDD data ribbon cable PJ5 on the
network controller PWB. Install a new network control PWB, PL 16.10 Item 1.
_________________________________________________________________________
GRUB Loading stage 1.5.
GRUB loading, please wait.....
Press any key to continue.
GRUB version 0.92 (639K / 12928 upper memory)
_________________________________________________________________________
Explanation
• The BIOS (Pre boot) attempts to load the network controller software from the HDD, and
hand off the boot up procedure to the Linux custom.
• Critical Checks
• If the boot sequence stops at "loading...", suspect corrupted software on the network con-
troller HDD, a loss of power, or bad connection to the network controller HDD or a defec-
tive network controller HDD, PL 16.10 Item 5.
_________________________________________________________________________
Booting Linux CUSTOM
Booting CUSTOM
Linux version 2.4.20-20.9.1 xerox -denali - opt
_________________________________________________________________________
Explanation
• The Linux custom has taken over the boot up and a File System check is being per-
formed.
NOTE: The File System check will occur during every network controller boot up.
Critical Check
• If the boot sequence stops or if any error messages appear in this section (bad block on
partition), suspect a defective network controller HDD, PL 16.10 Item 5.
_________________________________________________________________________
Setting system clock:Tue NOV 2 07:06:11 EST 2004
August 2007
2-700 WorkCentre 5687 Family