Table of Contents
Advertisement
11B-170 HCSS BM Initialization Failure RAP
When an initialization command is received from the machine, the units are initialized in three
stages:
•
The following units are initialized sequentially:
1.
The compiler carriage staple head is driven to the home position, unless already
home.
2.
The compiler carriage stapling unit is driven to the home position, unless already
home.
3.
The compiler carriage ejector is driven to the home position, unless already home.
•
The following units are then initialized simultaneously:
1.
The compiler carriage front tamper is driven to the home position, unless already
home.
2.
The compiler carriage rear tamper is driven to the home position, unless already
home.
3.
The hole punch is driven to the home position, unless already home.
4.
The compiler carriage paddle is driven to the home position, unless already home.
NOTE: The staple cartridge must be fully pushed home.
•
The following units of the BM are then initialized:
1.
The BM tampers are driven to the home position, unless already home.
2.
The BM backstop is driven to the home position, unless already home.
3.
The BM crease roll gate is driven to the home position, unless already home.
4.
The BM crease blade is driven to the home position, unless already home.
5.
The BM staple heads are driven to the home position, unless already home.
Initial Actions
Open the HCSS BM front door. Cheat the front door interlock switch and the top cover interlock
switch. Fully pull out the BM module.
Procedure
If the initialization sequence fails to place any unit at the home position, refer to the appropriate
RAPs:
•
The compiler carriage staple head is not at the home position, refer to 11-050-170, 11-
360-170 Compiler Carriage Staple Head Operation Failure RAP.
•
The compiler carriage stapling unit is not at the home position, refer to 11-053-170, 11-
370-170 Compiler Carriage Staple Head Unit Movement Failure RAP.
•
The compiler carriage ejector is not at the home position, refer to 11-320-170, 11-322-170
Compiler Ejector Movement Failure RAP.
•
The compiler carriage front tamper is not at the home position, refer to 11-005-170, 11-
006-170, 11-310-170, 11-311-170 Compiler Carriage Front Tamper Move Failure RAP.
•
The compiler carriage rear tamper is not at the home position, refer to 11-007-170, 11-
008-170, 11-312-170, 11-313-170 Compiler Carriage Rear Tamper Move Failure RAP.
•
The hole punch is not at the home position, refer to 11-043-170, 11-350-170 Hole Punch
Cycle Failure RAP
•
The compiler carriage paddle roll is not at the home position, refer to 11-024-170, 11-025-
170 Compiler Carriage Paddle Position Failure RAP.
Status Indicator RAPs
11B-170
•
The BM tampers are not at the home position, refer to 11-066-170, 11-384-170 HCSS BM
Tamper Failure RAP.
•
The BM backstop is not at the home position, refer to11-065-170, 11-383-170 HCSS BM
Backstop Failure RAP.
•
The BM crease roll gate is not at the home position, refer to 11-415-170 HCSS BM
Crease Roll Gate Failure RAP.
•
The BM crease blade is not at the home position, refer to 11-061-170, 11-416-170 HCSS
BM Creasing RAP.
•
Either of the BM staple heads are not at the home position, refer to 11-051-170 BM Staple
Head Cycle Failure RAP.
August 2007
2-524
WorkCentre 5687 Family
Hide quick links:
Advertisement
Chapters
Table of Contents
