11-030-130, 11-336-130 Bin 1 Movement Failure RAP
11-030-130 Bin 1 fails to move.
11-336-130 Bin 1 is not at the home position.
NOTE: The home position is at the uppermost position.
Initial Actions
•
Check that bin 1 is not damaged and there are no obstructions that would prevent bin 1
from moving. If necessary, install a new bin 1, PL 11.52 Item 4.
•
Press the manual staple button, PL 11.32 Item 10 to lower bin 1. Press again the manual
staple button to raise bin 1.
Procedure
NOTE: All HCSS interlocks must be made to supply +24V to the motors.
Enter dC330, codes 11-032 bin 1 elevator motor down to run the bin 1 elevator motor, MOT11-
030, Figure 1. MOT11-030 runs.
Y
N
Go to Flag 2. Check MOT11-030.
Refer to:
•
GP 10, How to Check a Motor.
•
P/J424, HCSS PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Bin 1 elevator motor, PL 11.52 Item 11.
•
HCSS PWB, PL 11.56 Item 5.
Enter dC330, codes 11-032 bin 1 elevator motor down, then 11-030 bin 1 elevator motor home
Figure 1. Bin 1 moves away from, then back to, the home position.
Y
N
Check the bin 1 front and rear elevator belts:
•
Ensure that both belts are correctly positioned on the upper and lower pulleys.
•
Ensure that bin 1 is securely clamped to both elevator belts.
Enter dC330, code 11-334, actuate the bin 1 upper limit switch, S11-334, Figure 1. The
play changes.
Y
N
Go to Flag 3. Check the switch S11-334.
Refer to:
•
GP 13, How to Check a Switch.
•
P/J424, HCSS PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary.
•
Bin 1 upper limit switch, PL 11.52 Item 1.
•
HCSS PWB, PL 11.56 Item 5.
A
Status Indicator RAPs
11-030-130, 11-336-130
A
Enter dC330, code 11-335, actuate the bin 1 lower limit switch, S11-335, Figure 1. The
play changes.
Y
N
Go to Flag 4. Check the switch S11-335.
Refer to:
•
GP 13, How to Check a Switch.
•
P/J424, HCSS PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary.
•
Bin 1 lower limit switch, PL 11.52 Item 2.
•
HCSS PWB, PL 11.56 Item 5.
Enter dC330, code 11-035, actuate the bin 1 empty sensor, Q11-035, Figure 1. The
changes.
Y
N
Go to Flag 1. Check the sensor Q11-035.
Refer to:
•
GP 11, How to Check a Sensor.
•
P/J416, HCSS PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Bin 1 empty sensor, PL 11.52 Item 5.
•
HCSS PWB, PL 11.56 Item 5.
Perform SCP 6 Final Actions.
dis-
August 2007
2-384
dis-
display
WorkCentre 5687 Family