Table of Contents
Advertisement
•
Enter dC330 code 11-023 Eject Mot Cycle, cycles the eject assembly, PL 11.114 Item 1.
•
Enter dC330 code 11-033 Bin 1 Elevator Motor Cycle, to move bin 1 up and down, PL
11.106 Item 8.
NOTE: The bin will move down and then move up to the home position.
Possible causes and potential solutions are:
•
2 knocks for each stapled set.
Possible causes are:
–
LCSS set ejector.
Solution:
–
Go to the 11-320-120, 11-322-120 Ejector Movement Failure RAP.
•
Clicking Noise from the LCSS.
Possible causes are:
–
The staple head continually operating for approximately 15 seconds. This occurs
every time the LCSS top cover or front door is opened then closed, because the sta-
pler is attempting to prime the staple head, by indexing the staple stick forward and
pre-forming two staples.
Solution:
–
Check the staple cartridge for jammed staples and remove any that are found.
–
Ensure the staple cartridge is fully seated.
–
Ensure that the correct staple cartridge is installed.
–
Perform 11-364-120 Stapling Failure RAP.
LCSS 2K
Run the following components:
•
Enter dC330 code 11-000 Transport Motor 1, to run the entry transport rolls, PL 11.14
Item 6.
•
Enter dC330 code 11-001 Transport Motor 2, to run the entry rolls, PL 11.22 Item 5.
•
Enter dC330 code 11-024 Paddle wheel Motor run, rotates the paddle wheel, PL 11.8
Item 4.
•
Enter dC330 code 11-009 Tamp Mot Cycle, cycles the front and rear tampers, PL 11.16
Item 1.
•
Enter dC330 code 11-023 Eject Mot Cycle, cycles the eject assembly, PL 11.18 Item 1.
•
Enter dC330 code 11-033 Bin 1 Elevator Motor Cycle, to move bin 1 up and down, PL
11.10 Item 8.
NOTE: The bin will move down and then move up to the home position.
•
Enter dC330 code 11-043 Punch Head run, rotates the punch head, PL 11.6 Item 3.
•
Enter dC330 code 11-055 SU1 index Mot Cycle, cycles the stapler from the front to the
rear, PL 11.20 Item 5.
Possible causes and potential solutions are:
•
2 knocks for each stapled set.
Solution:
–
Go to the 11-320-110, 11-322-110 Ejector Movement Failure RAP.
•
Noise from the right hand side of the machine.
Status Indicator RAPs
OF1
Possible causes are:
–
The LCSS is not aligned correctly.
Solution:
–
Check the machine to LCSS alignment, ADJ 11.2-110.
–
Adjust the components if appropriate.
–
Install new parts as necessary.
•
Clicking Noise from the LCSS
Possible causes are:
–
The staple head continually operating for approximately 15 seconds. This occurs
every time the LCSS top cover or front door is opened then closed, because the sta-
pler is attempting to prime the staple head, by indexing the staple stick forward and
pre-forming two staples.
Solution:
–
Check the staple cartridge for jammed staples and remove any that are found.
–
Ensure the staple cartridge is fully seated.
–
Ensure that the correct staple cartridge is installed.
–
Perform 11-364-110 Stapling Failure RAP.
HCSS
Run the following components:
Make sure that the first tamper in the compiler carriage is returned to the home position before
the second tamper is checked in diagnostics.
•
Enter dC330 code 11-000 Transport Motor 1, to run the vertical paper transport, PL 11.40,
PL 11.42 and input transport roll, PL 11.38.
•
Enter dC330 code 11-001 Transport Motor 2, to run the compiler entry shaft, PL 11.48
Item 16 and the transport shaft PL 11.49 Item 8.
•
Enter dC330 code 11-003 Tamp. Mot. Front Home, to move the front tamper to the home
position PL 11.46 Item 10.
•
Enter dC330 code 11-004 Tamp. Mot. Rear Home, to move the rear tamper to the home
position, PL 11.46 Item 10.
•
Enter dC330 code 11-005 Tamp. Mot. Front Move, to move the front tamper to the centre
of the compiler, PL 11.46 Item 10.
•
Enter dC330 code 11-006 Tamp. Mot. Rear Move, to move the rear tamper to the centre
of the compiler tray, PL 11.46 Item 10.
•
Enter dC330 code 11-010 CC Eject Roll Motor, to run the compiler carriage eject rolls, PL
11.49 Item 1.
•
Enter dC330 code 11-014 CC Motor Move Up, to raise the compiler carriage, PL 11.44
Item 12.
•
Enter dC330 code 11-016 CC Motor Move Down, to lower the compiler carriage, PL 11.44
Item 12.
•
Enter dC330 code 11-023 Eject Mot. cycle, to cycle the eject housing assembly, PL 11.47
Item 11.
•
Enter dC330 code 11-025 Paddle Roll Motor Run, to rotate the paddle rolls, PL 11.47 Item
8.
•
Enter dC330 code 11-030 Bin 1 Elevator Motor Home, to move Bin 1 up to the home posi-
tion, PL 11.52.
August 2007
2-734
CAUTION
WorkCentre 5687 Family
Hide quick links:
Advertisement
Chapters
Table of Contents
