Table of Contents
Advertisement
11-120-130, 11-122-130 Compiler Carriage Jam RAP
11-120-130 The lead edge of a sheet is late arriving at the compiler sensor.
11-122-130 the trail edge of a sheet or set is late leaving the compiler sensor.
Initial Actions
•
Check for a paper jam in the compiler or in the paper path to the compiler.
•
Ensure the paper tray guides are set to the correct position for the size of paper in all
trays.
For trays 3 and 4 perform the following:
1.
Select the systems settings button from the tools screen.
2.
Select the tray management button and stock settings.
3.
From the list, select tray 3. Select the change stock size button.
4.
Select the paper size loaded in the tray. Select the save button.
5.
Repeat for tray 4.
6.
Save the stock settings and exit the tools mode.
•
Check the inner paper guide nips and the mylar guide, PL 11.40 Item 16, Figure 2.
•
Check the condition of the compiler belts. Lift the shutter, PL 11.47 Item 6.
Rotate the jam clearance knob 5C and check that both compiler belts rotate freely, Figure
3, PL 11.49 Item 12.
•
Check that the HCSS is correctly aligned with the machine, refer to ADJ 11.1-130
Machine to HCSS alignment.
Procedure
NOTE: All HCSS interlocks must be made to supply +24V to the motors.
Enter dC330, code 11-120. Actuate the compiler sensor, Q11-120, Figure 1. The
changes.
Y
N
Go to Flag 1. Check the sensor, Q11-120.
Refer to:
•
GP 11 How to Check a Sensor.
•
P/J409, Carriage PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Carriage PWB, PL 11.46 Item 5.
•
Compiler sensor, PL 11.48 Item 7.
Enter dC330, code 11-001 to run transport motor 2, MOT 11-001. The motor runs.
Y
N
Go to Flag 3. Check the motor MOT 11-001.
Refer to:
•
GP 10, How to Check a Motor.
•
P/J403, Carriage PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Carriage PWB, PL 11.46 Item 5.
A
Status Indicator RAPs
11-120-130, 11-122-130
A
•
Transport motor 2, PL 11.48 Item 18.
Enter dC330, code 11-010 to run the compiler carriage eject roll motor, MOT 11-010. The
motor runs.
Y
N
Go to Flag 2. Check the motor MOT 11-010.
Refer to:
•
GP 10, How to Check a Motor.
•
P/J408, Carriage PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Carriage PWB, PL 11.46 Item 5.
•
Compiler carriage eject roll motor, PL 11.49 Item 1.
Enter dC330, code 11-023 to run the eject motor, MOT 11-020. The eject housing cycles
between open and closed.
Y
N
Go to Flag 4. Check the motor MOT 11-020.
Refer to:
•
GP 10, How to Check a Motor.
•
P/J406, Carriage PWB.
•
11C-130 HCSS Power Distribution RAP.
Install new parts as necessary:
•
Carriage PWB, PL 11.46 Item 5.
•
Eject motor assembly, PL 11.47 Item 2.
Enter dC330, code 11-000 to run the transport motor 1B, Figure 2. The motor runs.
display
Y
N
Go to Flag 6 and check transport motor 1B.
Refer to:
•
GP 10, How to Check a Motor.
•
P/J425, HCSS PWB
•
11C-130 HCSS Power Distribution RAP.
Install new components as necessary:
•
Transport motor 1B, PL 11.38 Item 5.
•
HCSS PWB, PL 11.56 Item 5.
Check the transport motor 1B drive belt and belt tensioner. If necessary install new parts:
•
Transport motor 1B drive belt, PL 11.38 Item 3.
•
Belt tensioner, PL 11.38 Item 1.
Go to Flag 5, check the harness and connectors P/J412 and P/J432, refer to GP 7. The wir-
ing and connectors are good.
Y
N
Repair the wiring or install new components.
Perform SCP 6 Final Actions.
August 2007
2-404
WorkCentre 5687 Family
Hide quick links:
Advertisement
Chapters
Table of Contents
