Power control (PWR)
31
30
29
Res.
Res.
Res.
Res.
15
14
13
PU15
PU14
PU13
PU12
rw
rw
rw
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:0 PUy: Port E pull-up bit y (y = 0 to 15)
Setting PUy bit while the corresponding PDy bit is zero and the APC bit of the PWR_CR3
register is set activates a pull-up device on the PE[y] I/O.
1. Only applies to STM32G0B1xx and STM32G0C1xx devices. Reserved for the other devices.
4.4.17
Power Port E pull-down control register (PWR_PDCRE)
Address offset: 0x44
Reset value: 0x0000 0000. This register is not reset when exiting Standby modes and with
PWRRST bit in the
Access: Additional APB cycles are needed to access this register vs. a standard APB
access (3 for a write and 2 for a read).
31
30
29
Res.
Res.
Res.
Res.
15
14
13
PD15
PD14
PD13
PD12
rw
rw
rw
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:0 PDy: Port E pull-down bit y (y = 0 to 15)
Setting PDy bit while the APC bit of the PWR_CR3 register is set activates a pull-down
device on the PE[y] I/O.
1. Only applies to STM32G0B1xx and STM32G0C1xx devices. Reserved for the other devices.
4.4.18
Power Port F pull-up control register (PWR_PUCRF)
Address offset: 0x48
Reset value: 0x0000 0000. This register is not reset when exiting Standby modes and with
PWRRST bit in the
Access: Additional APB cycles are needed to access this register vs. a standard APB
access (3 for a write and 2 for a read).
156/1390
28
27
26
25
Res.
Res.
Res.
12
11
10
9
PU11
PU10
PU9
rw
rw
rw
rw
APB peripheral reset register 1
28
27
26
25
Res.
Res.
Res.
12
11
10
9
PD11
PD10
PD9
rw
rw
rw
rw
APB peripheral reset register 1
24
23
22
Res.
Res.
Res.
8
7
6
PU8
PU7
PU6
rw
rw
rw
(1)
(RCC_APBRSTR1).
24
23
22
Res.
Res.
Res.
8
7
6
PD8
PD7
PD6
rw
rw
rw
(1)
(RCC_APBRSTR1).
RM0444 Rev 5
21
20
19
18
Res.
Res.
Res.
Res.
5
4
3
2
PU5
PU4
PU3
PU2
rw
rw
rw
rw
21
20
19
18
Res.
Res.
Res.
Res.
5
4
3
2
PD5
PD4
PD3
PD2
rw
rw
rw
rw
RM0444
17
16
Res.
Res.
1
0
PU1
PU0
rw
rw
17
16
Res.
Res.
1
0
PD1
PD0
rw
rw
Need help?
Do you have a question about the STM32G0 1 Series and is the answer not in the manual?
Questions and answers