Table of Contents
Advertisement
08-102 Tray 2 Misfeed RAP
08-102 The lead edge of the paper failed to actuate the tray 2 feed sensor within the correct
time after feeding paper from tray 2.
Initial Actions
•
Check the condition of the paper in tray 2. Refer to IQ1 and GP 20.
•
Check that the paper guides are set correctly.
•
Check that the left hand door is latched correctly.
•
Check that the interlock cover has not come loose, PL 7.30 Item 23. Bias the cover to the
right and tighten the two screws
•
Check for damage to the chamfered edge on the left side of the tray. Repair the damaged
edge or install a new paper tray, PL 7.10 Item 1.
Procedure
CAUTION
Do not manually lower the feed head, always use the paper tray to activate the feed head.
Manually lowering the feed head will damage the paper feed assembly.
NOTE: The front door interlock must be cheated when checking +24V components.
Enter dC330 code 08-102 tray 2 feed sensor, Q08-102. Figure 1. Press Start. Open the left
hand door and manually actuate the sensor. The display changes.
Y
N
Go to Flag 1.Check Q08-102. Refer to:
•
GP 11 How to Check a Sensor.
•
P/J276, Tray 1 and 2 control PWB.
•
01E +5V Distribution RAP.
•
01B 0V Distribution RAP.
Install new components as necessary:
•
Tray 2 feed sensor, PL 7.30 Item 24.
•
Tray 1 and 2 control PWB, PL 7.10 Item 2.
Enter dC330 code 08-025 tray 1 and 2 transport motor, MOT08-025. Press Start. The
runs.
Y
N
Go to Flag 2. Check MOT08-025. Refer to:
•
GP 10 How to Check a Motor.
•
P/J273, Tray 1 and 2 control PWB.
•
01G +24V Distribution RAP.
•
01B 0V Distribution RAP.
Install new components as necessary:
•
Tray 1 and 2 transport motor, PL 8.25 Item 5.
•
Tray 1 and 2 control PWB, PL 7.10 Item 2.
The transport rolls rotate.
Y
N
Check the drive belt and gears, GP 7, PL 8.25 Item 2.
A
Status Indicator RAPs
08-102
A
To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 08-
020 is run in diagnostics.
Enter dC330 code 08-020 tray 2 paper feed motor, MOT08-020. Pull out the tray. Press Start.
The motor runs.
Y
N
Go to Flag 3. Check MOT08-020. Refer to:
•
GP 10 How to Check a Motor.
•
P/J275, Tray 1 and 2 control PWB.
•
01E +5V Distribution RAP.
•
01G +24V Distribution RAP.
•
01B 0V Distribution RAP.
Instal new Components as necessary:
•
Tray 2 feed motor, PL 8.26 Item 6.
•
Tray 1 and 2 control PWB PL 7.10 Item 2.
Perform the following:
•
Clean the feed roll using a cloth dampened with water.
•
Check the feed roll assembly, PL 8.26 Item 3.
•
Check the feed assembly, PL 8.26 Item 2.
motor
August 2007
2-192
CAUTION
WorkCentre 5687 Family
Hide quick links:
Advertisement
Chapters
Table of Contents
