2. Implementing Protocols in Arria 10 Transceivers
UG-01143 | 2018.06.15
Document
Version
Made the following changes to the CPRI section:
•
Updated the "Connection Guidelines for a CPRI PHY Design" figure.
•
Added table for the "Behavior of word aligner status signals for varying interface widths", when in
Manual Mode.
Made the following changes to the Other Protocols section:
•
Updated the "Connection Guidelines for a PCS Direct PHY Design" figure.
•
Updated the "Connection Guidelines for an Enhanced PCS in Low Latency Mode Design" figure.
•
Updated the description following the "Rate Match FIFO Insertion with Four Skip Patterns Required
for Insertion" figure.
•
Added a Note to the "TX Bit Slip" section.
•
Changed the value for rx_parallel_data in the "TX Bit Slip in 8-bit Mode" and "TX Bit Slip in 16-bit
Mode" figures.
Made the following changes to the XAUI PHY IP Core section:
•
Removed the
section.
Made the following changes to the Using the Arria 10 Transceiver Native PHY IP Core section:
•
Updated the figure for Transceiver Native PHY IP Core Parameter Editor.
•
PMA parameters
— Updated the PMA parameter categorization in the TX PMA and RX PMA "Equalization" section.
— Added parameters
— Added parameters
— Updated "RX PMA Parameters" table into "RX CDR Options" and "Equalization" sections.
— Removed the option
— Updated the description of "CTLE Adaptation Mode" and "DFE Adaptation Mode" in "RX PMA"
— Updated value and description for parameter
— Updated value and description for parameter
2014.12.15
Made the following changes to the Using the Arria 10 Transceiver Native PHY IP Core section:
•
Updated the description of
•
Added a new section Enhanced PCS TX and RX Control Ports to better describe the
and
tx_control
•
Updated the clock domain information about signals mentioned in
•
Updated the description of
•
Updated the parameter descriptions in General Datapath Parameters and PMA Parameters sections.
•
Updated the port descriptions in PMA Ports section.
Made the following changes to the Interlaken section:
•
Added another value to the "TX channel bonding mode" parameter in the "TX PMA Parameters"
table.
•
Added values to the "PCS TX channel bonding master" and "Actual PCS TX channel bonding master"
parameters in the "TX PMA Parameters" table.
•
Corrected the values to the "CTLE adaptation mode" parameter in the "RX PMA Parameters" table.
•
Added the "Enable Interlaken TX random disparity bit" parameter to the "Interlaken Disparity
Generator and Checker Parameters" table.
•
Changed the values to four parameters to "Off" in the "Gearbox Parameters" table.
•
Removed the "Enable embedded debug" parameter from the "Dynamic Reconfiguration Parameters"
table.
Made the following changes to the Gigabit Ethernet (GbE) and GvE with IEEE 1588v2 section:
•
Added a figure description to the "Signals and Ports for Native PHY IP Configured for GbE or GbE
with IEEE 1588v2" figure.
constraint from the "XAUI PHY Timing Analyzer SDC Constraints"
set_max_skew
Enable tx_pma_iqtxrx_clkout port
in "TX PMA Optional Ports" table.
port
Enable rx_pma_iqtxrx_clkout port
Enable rx_pma_div_clkout division
ports table.
parameter table.
tx_pma_div_clkout port
rx_pma_div_clkout port
tx_cal_busy
bit encodings used for different protocols. Removed the bit encodings for
rx_control
and
signals from Enhanced PCS Ports section.
rx_control
rx_std_wa_patternalign
Changes
Enable tx_pma_clkout port
in "TX Bonding Options" table.
Enable rx_pma_clkout port
in "RX PMA Optional Ports" table.
and
signals in the PMA Ports section.
rx_cal_busy
signal in Standard PCS Ports section.
®
Intel
and
Enable tx_seriallpbken
in "RX PMA Optional Ports" table.
factor from RX PMA optional
and
Enable
and
Enable
tx_control
section.
Enhanced PCS Ports
continued...
®
Arria
10 Transceiver PHY User Guide
341