Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 154

4
Commands Quick Reference
Table 64 :WGEN<w> Commands Summary (continued)
Command
:WGEN<w>:ARBitrary:DA
TA:DAC {<binary> |
<value>, <value> ...}
(see page 1063)
:WGEN<w>:ARBitrary:IN
Terpolate {{0 | OFF}
| {1 | ON}} (see
page 1064)
:WGEN<w>:ARBitrary:ST
ORe <source> (see
page 1065)
:WGEN<w>:FREQuency
<frequency> (see
page 1066)
:WGEN<w>:FUNCtion
<signal> (see
page 1067)
:WGEN<w>:FUNCtion:PUL
Se:WIDTh <width> (see
page 1070)
:WGEN<w>:FUNCtion:RAM
P:SYMMetry <percent>
(see page 1071)
:WGEN<w>:FUNCtion:SQU
are:DCYCle <percent>
(see page 1072)
154
Query
n/a
:WGEN<w>:ARBitrary:IN
Terpolate? (see
page 1064)
n/a
:WGEN<w>:FREQuency?
(see page 1066)
:WGEN<w>:FUNCtion?
(see page 1069)
:WGEN<w>:FUNCtion:PUL
Se:WIDTh? (see
page 1070)
:WGEN<w>:FUNCtion:RAM
P:SYMMetry? (see
page 1071)
:WGEN<w>:FUNCtion:SQU
are:DCYCle? (see
page 1072)
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Options and Query Returns
<binary> ::= decimal 16-bit
integer values between -512 to
+511 in IEEE 488.2 binary block
format
<value> ::= decimal integer
values between -512 to +511 in
comma-separated NR1 format
<w> ::= 1 or 2 in NR1 format
{0 | 1}
<w> ::= 1 or 2 in NR1 format
<source> ::= {CHANnel<n> |
WMEMory<r> | FUNCtion<m> |
MATH<m>}
<n> ::= 1 to (# analog channels)
in NR1 format
<r> ::= 1 to (# ref waveforms) in
NR1 format
<m> ::= 1-4 in NR1 format
<w> ::= 1 or 2 in NR1 format
<frequency> ::= frequency in Hz
in NR3 format
<w> ::= 1 or 2 in NR1 format
<signal> ::= {SINusoid | SQUare |
RAMP | PULSe | NOISe | DC | SINC
| EXPRise | EXPFall | CARDiac |
GAUSsian | ARBitrary}
<w> ::= 1 or 2 in NR1 format
<width> ::= pulse width in
seconds in NR3 format
<w> ::= 1 or 2 in NR1 format
<percent> ::= symmetry
percentage from 0% to 100% in NR1
format
<w> ::= 1 or 2 in NR1 format
<percent> ::= duty cycle
percentage from 20% to 80% in NR1
format
<w> ::= 1 or 2 in NR1 format