012-152 Compiler Exit Sensor On Jam Rap (Lx); 012-161 Finisher Set Eject Jam Rap (Lx) - Xerox workcentre 5335 series Service Manual

012-152 Compiler Exit Sensor On Jam RAP (LX)

BSD-ON: BSD 12.16 - Office Finisher LX Transportation
After the H-Transport Exit Sensor turned On, the Compiler Exit Sensor did not turn On within
the specified time.
Initial Actions
• Ensure that Chute Assembly (PL 23.14
• Power OFF/ON
Procedure
Execute Component Control [012-150], Compiler Exit Sensor. Actuate the Compiler Exit Sen-
sor (PL 23.14). The display changes.
Y N
Check the wire between J8869 pin 2 and
loose or damaged connector. The wire is OK.
Y N
Repair/reconnect as required.
Measure the voltage between P/J8988, pins 6 and 4 on the Finisher PWB. The voltage
is approx. +5VDC.
Y N
Replace the Finisher PWB (PL
Measure the voltage between P/J8988, pin 5 on the Finisher PWB and GND. Actuate the
Compiler Exit Sensor. The voltage changes.
Y N
Replace the Compiler Exit Sensor
Replace the Finisher PWB (PL 23.16).
Execute Component Control [012-038], Transport Motor. The Transport Motor rotates.
Y N
Check the wires between P/J8879 on the Transport Motor and
PWB for an open or short circuit, or a loose or damaged connector. The wires are OK.
Y N
Repair/reconnect as required.
Measure the resistance of the Transport Motor between each pin P/J8879-1/2/5/6.
resistance is approx. 20 Ohm.
Y N
Replace the Transport Motor (PL
Replace the Finisher PWB (PL 23.16). If the problem persists, replace the Transport
Motor (PL 23.13).
Check the Exit Roller, Entrance Roller, Paddle Shaft and Eject Belt for wear, damage or con-
tamination (PL 23.13).
Check the Compiler Exit Sensor and Transport Motor circuits for an intermittent condition.
If the problem continues, replace the Finisher PWB
Status Indicator RAPs
012-152, 012-161
Item 16) is present and properly installed.
P/J8988 pin 5 for an open or short circuit, or a
23.16).
(PL 23.14).
P/J8983 on the Finisher
23.13).
(PL 23.16).
BUS Updated 12/2011

012-161 Finisher Set Eject Jam RAP (LX)

BSD-ON: BSD 12.19 - Office Finisher LX Tamping & Offset (2 of 2)
BSD-ON: BSD 12.22 - Office Finisher LX Eject Control (1 of 2)
After the Eject Motor turned On, the Compiler Tray No Paper Sensor did not turn Off within the
specified time.
Procedure
Enter Component Control [012-151], Compiler Tray No Paper Sensor. Select Start. Actuate
the Compiler Tray No Paper Sensor. The display changes.
Y N
Check the wire between J8880
or short circuit, or a loose or damaged connector. The wire is OK.
Y N
Repair/reconnect as required.
Measure the voltage between
approx. +5VDC.
Y N
Replace the Finisher PWB
Measure the voltage between
Office Finisher LX Tamping & Offset (2 of 2)
sor. The voltage changes.
Y N
Replace the Compiler Tray No Paper Sensor
Replace the Finisher PWB (PL
Alternately execute Component Control
Control [012-055 Eject Motor FORWARD HI]. The Eject Motor starts up.
Y N
Check the wires between P/J8878
(BSD 12.22 - Office Finisher LX Eject Control (1 of
loose or damaged connector. The wires are OK.
Y N
Repair/reconnect as required.
The
Measure the resistance of the Eject Motor between each point of P/J8878-1/3/4/6. The
resistance is approx. 20 Ohm.
Y N
Replace the Eject Motor
Replace the Eject Motor (PL
23.16).
Check the Exit Roller, Entrance Roller, Paddle Shaft and Eject Belt for wear, damage or con-
tamination (PL 23.13).
Check the Compiler Tray No Paper Sensor and Eject Motor circuits for an intermittent condi-
tion.
07/2011
2-108
pin 2 and P/J8994 pin 2 on the Finisher PWB for an open
P/J8994 pins 3 and 1 on the Finisher PWB. The voltage is
(PL 23.16).
P/J8994 pin 2 on the Finisher PWB and GND
Actuate the Compiler Tray No Paper Sen-
(PL 23.12).
23.16).
[012-054 Eject Motor FORWARD LO] and
on the Eject Motor and P/J8983 on the Finisher PWB
2)) for an open or short circuit, or a
(PL 23.11).
23.11). If the problem persists, replace the Finisher PWB
WorkCentre 5335 Family Service Documentation
(BSD 12.19 -
Component
(PL
Initial Issue