Table of Contents
Advertisement
A
B
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB
Enter [012-054] and [012-056] alternately. The Eject Motor rotates.
Y
N
Check the connections of
P/J8706
and P/J8741.
connected.
Y
N
Connect
P/J8706
and
P/J8741
Check for an open or short circuit between
P/J8706
and
P/J8741
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8706-13 (+) and GND (-), and between
P/J8706-15 (+) and GND (-). The voltage is approx. +24VDC.
Y
N
Go to
Integrated Finisher Wirenets
Check the Eject Motor drive mechanism for deformed parts, broken parts, and/or belt
damage The drive mechanism free from defects.
Y
N
Repair defects or damage to the drive mechanism.
Replace the Eject Motor
(PL
22.9). If the problem continues, replace the Finisher PWB
(PL
22.7).
Check the wires and connectors for an intermittent open or short circuit. If the problem contin-
ues, replace the Finisher PWB
(PL
22.7).
Initial Issue
WorkCentre 5335 Family Service Documentation
(PL
22.7).
P/J8706
and
P/J8741
are securely
securely.
P/J8706
and P/J8741. The wires between
and check the +24VDC circuit.
BUS Updated 12/2011
012-211 (Integrated Finisher) Stacker Tray Fail RAP
BSD-ON:
BSD 12.8 - Integrated Finisher Stacker Tray Control
•
Within a specified time after the Stacker Tray started lifting up, the Stack Height Sensor
did not detect the lifting up of the Stacker Tray.
•
Within a specified time after the Stacker Tray started going down at initialization and dur-
ing a job, the lower position of the tray (Full) could not be detected based on the changes
in the Stacker Stack Sensor 1 and the Stacker Stack Sensor 2.
Initial Actions
•
Check the Stack Height Sensor is properly installed, not broken, and has no foreign
object.
•
Check the Stacker Stack Sensors 1 and 2 are properly installed and have no foreign
objects and that their actuators are not broken.
•
Power Off/On.
Procedure
Check the drive mechanism to the Stacker Tray for a deformed or broken part and not-seated
gears. The mechanism is free from defects and the gears seat properly.
Y
N
Repair the mechanism.
Enter
Component Control
[012-267]. Block and unblock the Stack Height Sensor with a piece
of paper. The display changes.
Y
N
Check the connections of
P/J8708
connected.
Y
N
Connect
P/J8708
and
P/J8727
Check for an open or short circuit between
P/J8708
and
P/J8727
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8708-3 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
Measure the voltage between Finisher PWB P/J8708-2 (+) and GND (-). Block and
unblock the Stack Height Sensor with a piece of paper. The voltage changes.
Y
N
Replace the Stack Height Sensor
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB
Enter [012-278]. Block and unblock the Stacker Stack Sensor 1 by rotating the actuator. The
display changes.
07/2011
012-161 (Integrated Finisher), 012-211 (Integrated
2-91
and P/J8727.
P/J8708
and
P/J8727
are securely
securely.
P/J8708
and P/J8727. The wire between
and check the +5VDC circuit.
(PL
22.10).
(PL
22.7).
Status Indicator RAPs
Advertisement
Table of Contents
