YASKAWA HV600 Manual page 56

1.10 H: Terminal Functions
Setting Value Function
52 Sequence Timer Cancel
60 DC Injection Braking
Command
61 Speed Search from Fmax
62 Speed Search from Fref
63 Field Weakening
65 KEB Ride-Thru 1
Activate (N.C.)
66 KEB Ride-Thru 1
Activate (N.O.)
67 Communications Test
Mode
68 High Slip Braking (HSB)
Activate
69 Jog Run 2
6A Drive Enable
6D AUTO Command
6E HAND Command
70 Drive Enable 2
77 ASR Gain (C5-03) Select
7A KEB Ride-Thru 2
Activate (N.C.)
56
V/f OLV/PM EZOLV OLV/PM
Sets the command to cancel the currently active Sequence Timer.
ON : Cancel Active Sequence Timer
V/f OLV/PM EZOLV OLV/PM
Sets the command to use DC Injection Braking to stop the motor.
Note:
When A1-02 = 8 [Control Method Selection = EZOLV], this function is available with a PM motor.
V/f OLV/PM EZOLV OLV/PM
Sets the function to start speed search using an external reference although b3-01 = 0 [Speed Search Selection at Start
= Disabled].
Note:
The drive will detect oPE03 [Multi-Function Input Setting Err] if you set H1-xx = 61 and 62 at the same time.
V/f OLV/PM OLV/PM EZOLV
Sets the function to use an external reference to start speed search although b3-01 = 0 [Speed Search Selection at Start
= Disabled].
Note:
The drive will detect oPE03 [Multi-Function Input Setting Err] if you set H1-xx = 61 and 62 at the same time.
V/f OLV/PM OLV/PM EZOLV
Sets the function to send the Field Weakening Level and Field Weakening Frequency Limit commands set in d6-01
[Field Weakening Level] and d6-02 [Field Weakening Frequency Limit] when the input terminal is activated.
V/f OLV/PM EZOLV OLV/PM
Sets operation of the KEB1 function through the KEB Ride-Thru 1 (N.C.).
ON : Normal operation
OFF : Deceleration during momentary power loss
V/f OLV/PM OLV/PM EZOLV
Sets operation of the KEB1 function through the KEB Ride-Thru 1 (N.O.).
ON : Deceleration during momentary power loss
OFF : Normal operation
V/f OLV/PM EZOLV OLV/PM
Set the function for the drive to self-test RS-485 serial communications operation.
V/f OLV/PM OLV/PM EZOLV
Sets the command to use high-slip braking to stop the motor.
V/f OLV/PM EZOLV OLV/PM
Causes the drive to ramp to the d1-17 [Jog Reference] frequency. The forward/reverse command from the 3-wire or 2-
wire 2 sequence sets the direction.
V/f OLV/PM OLV/PM EZOLV
Sets the function to show dnE [Drive Enabled] on the keypad and ignore Run commands when the terminal is OFF.
V/f OLV/PM OLV/PM EZOLV
Sets the command to operate the drive in AUTO Mode.
ON : AUTO Mode
OFF : OFF Mode or HAND Mode
V/f OLV/PM EZOLV OLV/PM
Sets the command to operate the drive in HAND Mode.
ON : HAND Mode
OFF : OFF Mode or AUTO Mode
V/f OLV/PM OLV/PM EZOLV
Sets the function to show dnE [Drive Enabled] on the keypad and ignore Run commands when the terminal is OFF.
ON : Run command is accepted.
OFF : Run command is disabled. When the drive is running, it stops according to b1-03 setting.
V/f OLV/PM EZOLV OLV/PM
Sets the function to switch the ASR proportional gain set in C5-01 [ASR Proportional Gain 1] and C5-03 [ASR
Proportional Gain 2].
ON : C5-03
OFF : C5-01
V/f OLV/PM EZOLV OLV/PM
Sets operation of the KEB2 function through the KEB Ride-Thru 2 (N.C.).
ON : Normal operation
OFF : Deceleration during momentary power loss
Description
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
Ref.
295
295
295
296
296
296
296
296
297
297
297
297
297
298
298
298