YASKAWA HV600 Manual page 147

1.20 Parameters that Change from the Default Settings with A1-02 [Control Method Selection]
*3 The setting range varies depending on the setting of E5-01 [PM Motor Code Selection] when A1-02 = 5 [Control Method Selection = PM
Open Loop Vector].
*4 The default setting changes when the drive model and E1-03 [V/f Pattern Selection] change.
*5 This is the value for 208 V class drives. Double the value for 480 V class drives.
*6 The default value changes when the drive model changes.
◆
A1-02 = 5 and 8 [OLV/PM and EZOLV]
No.
b2-13 Short Circuit Brake Time @ Stop
b3-02 SpeedSearch Deactivation Current
b3-08 Speed Estimation ACR P Gain
b3-09 Speed Estimation ACR I Time
b3-14 Bi-directional Speed Search
b3-24 Speed Search Method Selection
b8-19 E-Save Search Injection Freq
C2-01 S-Curve Time @ Start of Accel
C3-02 Slip Compensation Delay Time
C3-22 Motor 2 Slip Comp Delay Time
C4-01 Torque Compensation Gain
C4-02 Torque Compensation Delay Time
C5-01 ASR Proportional Gain 1
C5-02 ASR Integral Time 1
C5-03 ASR Proportional Gain 2
C5-04 ASR Integral Time 2
C5-06 ASR Delay Time
C6-02 Carrier Frequency Selection
E1-04 Maximum Output Frequency
E1-05 Maximum Output Voltage
E1-06 Base Frequency
E1-07 Mid Point A Frequency
E1-08 Mid Point A Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Voltage
E1-11 Mid Point B Frequency
E1-12 Mid Point B Voltage
E1-13 Base Voltage
L1-01 Motor Overload (oL1) Protection
L2-31 KEB Start Voltage Offset Level
L3-05 Stall Prevention during RUN
L3-20 DC Bus Voltage Adjustment Gain
L8-38 Carrier Frequency Reduction
n8-51 Pull-in Current @ Acceleration
o1-03 Frequency Display Unit Selection
*1 Enabled only when E9-01 = 1 [Motor Type Selection = Permanent Magnet (PM)]
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
Name Range
0.00 - 25.50
0 - 200
0.00 - 6.00
0.0 - 1000.0
0 - 1
1 - 2
10 - 300
0.00 - 10.00
0 - 10000
0 - 10000
0.00 - 2.50
0 - 60000
0.00 - 300.00
0.000 - 60.000
0.00 - 300.00
0.000 - 60.000
0.000 - 0.500
1 - F
40.0 - 400.0
*5
0.0 - 255.0
0.0 - 400.0
0.0 - 400.0
*5
0.0 - 255.0
0.0 - 400.0
*5
0.0 - 255.0
0.0 - 400.0
*5
0.0 - 255.0
*5
0.0 - 255.0
0 - 4
*5
0 - 100
0 - 3
0.00 - 5.00
0 - 3
0 - 200
0 - 3
Control Method (A1-02 Setting)
Unit
OLV/PM (5)
0.01 s 0.50
1% -
0.01 0.30
0.1 ms 2.0
1 -
1 -
1 Hz -
0.01 s 1.00
1 ms -
1 ms -
0.01 0.00
1 ms 100
0.01 -
0.001 s -
0.01 -
0.001 s -
0.001 s -
*2
1 2
0.1 Hz Determined by E5-01
0.1 V Determined by E5-01
0.1 Hz Determined by E5-01
0.1 Hz -
0.1 V -
0.1 Hz Determined by E5-01
0.1 V -
0.1 Hz -
0.1 V -
0.1 V -
1 4
1 V 50
1 2
0.01 0.65
1 -
1% 50
1 2
EZOLV (8)
*1
0.00
-
*2
0.60
10.0
0
*3
1
20
1.00
200
-
0.00
200
10.00
0.500
10.00
0.500
0.004
*2
2
-
-
-
-
-
-
-
-
-
-
*6
1
50
3
1
0.65
-
80
*7
0
147