YASKAWA HV600 Manual page 64

1.10 H: Terminal Functions
Setting Value Function
97 Low Feedback
9E Low PI Auxiliary Control
Level
9F High PI Auxiliary Control
Level
A9 RELAY Operator Control
AA Utility Delay
AB Thrust Mode
AC Setpoint Not Maintained
B2 BAS Interlock
B8 Pump Fault
B9 Transducer Loss
BA PI Auxiliary Control
Active
BB Differential Feedback
Exceeded
BC Sleep Active
BD Start Delay
BE Pre-Charge
C0 HAND Mode
C1 AUTO Mode
C2 OFF Mode
C3 Main Feedback Lost
C4 Backup Feedback Lost
64
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the drive is in a Low Feedback Condition as specified by Y1-08 [Low Feedback Level]
and Y1-09 [Low Feedback Lvl Fault Dly Time] and when the drive detects an LFB [Low Feedback Sensed] fault or an
LOFB [High Feedback Sensed] alarm.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the PI Aux Feedback Level is less than YF-09 [PI Aux Control Low Level Detect] or if the
drive detects an LOAUX [Low PI Aux Feedback Level] fault.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the PI Aux Feedback Level is more than YF-12 [PI Aux Control High Level Detect] or if
the drive detects an HIAUX [High PI Aux Feedback Level] fault.
V/f OLV/PM OLV/PM EZOLV
The terminal changes to OFF or ON when you push the RELAY (
to turn it OFF. When the terminal is OFF, push
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the drive is stopped and is waiting for the timer set in Y4-17 [Utility Start Delay] to
expire.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the output frequency is between 0.0 Hz and the value set in Y4-12 [Thrust Frequency] and
the Thrust Bearing function is active.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the drive detects NMS [Setpoint Not Met] condition.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the Run command is active or the drive is outputting the voltage. The drive will use this
as an actuation signal for an external damper.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when one of these faults is active: LFB [Low Feedback Sensed], HFB [High Feedback Sensed],
NMS [Setpoint Not Met], or EFx [External Fault (Terminal Sx)].
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the current into the analog input associated with PID feedback is more than 21 mA or less
than 3 mA, or an FDBKL [WIRE Break] Fault or an FDBKL [Feedback Loss Wire Break] Alarm is active.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the PI Auxiliary Controller has an effect on the output speed.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the difference between the PID Feedback and the value from the terminal set for H3-xx =
2D [Differential Feedback] is more than Y4-18 [Differential Level] for the time set in Y4-19 [Differential Lvl
Detection Time].
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the Sleep function is active and the drive is not operating.
Note:
The terminal will not activate for Sleep Boost function.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the Feedback is more than the start level or the Feedback is less than the Inverse PID and
the start timer is timing.
Note:
You must set Y1-04 [Sleep Wake-up Level] ≠ 0 and Y1-05 [Sleep Wake-up Level Delay Time] ≠ 0 to use this
function.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the drive is in Pre-Charge Mode.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the drive is in HAND Mode operation.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the drive is in AUTO Mode operation.
V/f OLV/PM OLV/PM EZOLV
The terminal activates when the drive is in OFF Mode operation.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the drive loses the main PID feedback.
V/f OLV/PM EZOLV OLV/PM
The terminal activates when the drive loses the backup PID feedback.
Description
) button. When the terminal is ON, push
to turn in ON.
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
Ref.
321
321
321
322
322
322
322
322
322
322
322
322
323
323
323
323
323
323
323
323