YASKAWA HV600 Manual page 607

oH..................................................................... 383
oH3 ................................................................... 352
oH4 ................................................................... 352
oL2 ................................................................... 386
Output Current Overload .......................................... 388
Output Phase Loss Detection ..................................... 384
Overload ............................................................. 386
Software Current Limit Selection ................................ 386
R
Ready
LED status........................................................... 515
Remove
Front cover .......................................................... 576
Terminal cover ...................................................... 576
RESET key............................................................... 509
Restore
Parameters (Auto Backup) ........................................ 558
Parameters (keypad to drive) ..................................... 538
Reverse Operation Selection........................................... 182
RJ-45 connector ......................................................... 509
Rotational Auto-Tuning
Induction Motor .................................................... 561
PM Motors .......................................................... 561
Precautions .......................................................... 565
RUN
LED status........................................................... 515
Run command ........................................................... 179
Run Command at Power Up ........................................... 186
S
S-curve characteristics
Parameter ............................................................ 225
Sampling time setting
Data log .............................................................. 554
Sequence Timer
HOME screen display.............................................. 434
Sequence Timers ........................................................ 431
Serial communication terminals
MEMOBUS/Modbus Communications ......................... 592
Set date and time
Operation ............................................................ 549
Set time
Operation ............................................................ 549
Setpoint selection
System Feedback Monitor......................................... 495
Short Circuit Braking
Parameter ............................................................ 187
Side-by-side
Derating.............................................................. 387
Simple Positioning Stop................................................ 243
Sleep Function
Sleep.................................................................. 472
Wake-up ............................................................. 472
Sleep Wake-up level
Absolute Mode...................................................... 472
Delta to Setpoint Mode ............................................ 472
Slip compensation
Parameter ............................................................ 226
Softcharge Relay Maintenance Set ................................... 422
Software Current Limit Selection
Protective function ................................................. 386
Software version
Display procedure .................................................. 557
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
Speed Agreement
Parameter ............................................................ 368
Speed Detection
Parameter ............................................................ 368
Speed Estimation Speed Search ....................................... 192
Speed Search function
Operation during momentary power loss........................ 356
Parameter ............................................................ 190
Staging
Staging Mode ....................................................... 487
Stall Prevention function
Parameter ............................................................ 360
Stationary Auto-Tuning
Induction Motor .................................................... 561
PM Motors .......................................................... 561
Precautions .......................................................... 565
Stationary Auto-Tuning for Line-to-Line Resistance .............. 561
Precautions .......................................................... 565
Stator resistance Auto-Tuning ......................................... 561
Precautions .......................................................... 565
Stop command ........................................................... 179
Stopping Method Selection ............................................ 179
T
Terminal block........................................................... 592
Control circuit terminal block functions......................... 589
I/O terminals function selection switches ....................... 597
Terminal function selection
Terminal A1 ................................................... 597–598
Terminal A2 ................................................... 597–598
Terminal AM.................................................. 597, 599
Terminal FM .................................................. 597, 599
Terminal screw
Screwdriver........................................................... 10
Termination resistor
Setting switch ....................................................... 599
Test run
Checklist ............................................................. 571
Fine tuning .......................................................... 568
Procedure ............................................................ 517
Procedure for no-load test run .................................... 566
Procedure for test run with actual load .......................... 567
Thrust Mode
Thrust frequency.................................................... 476
Tightening torque
Control circuit terminals........................................... 594
Timer function
Parameter ............................................................ 199
Torque Compensation
Parameter ............................................................ 227
Torque limit function
Parameter ............................................................ 381
Trend Plot
Monitors ............................................................. 530
Tuning .................................................................... 222
U
U2, U3 Initialization .................................................... 422
Undertorque detection
Parameter ............................................................ 375
Unit selector ............................................................. 415
Up command....................................................... 285, 287
Parameter ...................................................... 242–243
USB port ................................................................. 509
607