YASKAWA HV600 Manual page 303

Setting Value
B Torque Detection 1 (N.O.)
C Frequency Reference Loss
E Fault
*1
F Not Used
10 Alarm
11 Fault Reset Command Active
12 Timer Output
13 Speed Agree 2
14 User-Set Speed Agree 2
15 Frequency Detection 3
16 Frequency Detection 4
17 Torque Detection 1 (N.C.)
18 Torque Detection 2 (N.O.)
19 Torque Detection 2 (N.C.)
1A During reverse
1B During Baseblock (N.C.)
1C Motor 2 Selected
1E Executing Auto-Restart
1F Motor Overload Alarm (oL1)
20 Drive Overheat Pre-Alarm (oH)
21 Safe Torque OFF
2F Maintenance Notification
30 During Torque Limit
37 During Frequency Output
38 Drive Enabled
39 Watt Hour Pulse Output
3A Drive Overheat Alarm
3D During Speed Search
42 Pressure Reached
4A During KEB Ride-Thru
4B During Short Circuit Braking
4C During Fast Stop
4D oH Pre-Alarm Reduction Limit
51 Sequence Timer 1
52 Sequence Timer 2
53 Sequence Timer 3
54 Sequence Timer 4
*1 Inverse output is not available.
*2 You cannot set this parameter on models 2169 to 2273 and 4065 to 4302.
■
Extended MFDO1 to MFDO3 Function Selection
You can set MFDO functions to bit 0 to bit 2 [MEMOBUS MFDO1 to 3] of MEMOBUS register 15E0 (Hex.). Use
H2-40 to H2-42 [Mbus Reg 15E0h bit0 to bit2 Output Func] to select the function.
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
Function Reference
312
312
312
312
312
312
312
313
313
314
314
315
315
315
316
316
316
316
316
317
317
317
317
317
318
318
318
318
318
319
319
319
319
319
319
319
320
Setting Value Function
58 UL6 Underload Detected
60 Internal Cooling Fan Failure
61 Pole Position Detection Complete
62 Modbus Reg 1 Status Satisfied
63 Modbus Reg 2 Status Satisfied
69 External Power 24V Supply
6A Data Logger Error
71 Low PI2 Control Feedback Level
72 High PI2 Control Feedback Level
89 Output Current Lim
90 to 92 DWEZ Digital Outputs 1 to 3
94 Loss of Prime
95 Thermostat Fault
96 High Feedback
97 Low Feedback
9E Low PI Auxiliary Control Level
9F High PI Auxiliary Control Level
A9 RELAY Operator Control
AA Utility Delay
AB Thrust Mode
AC Setpoint Not Maintained
B2 BAS Interlock
B8 Pump Fault
B9 Transducer Loss
BA PI Auxiliary Control Active
BB Differential Feedback Exceeded
BC Sleep Active
BD Start Delay
BE Pre-Charge
C0 HAND Mode
C1 AUTO Mode
C2 OFF Mode
C3 Main Feedback Lost
C4 Backup Feedback Lost
Inverse Outputs of 0 to C4
Sets an inverse output of the function for the MFDO.
100 to 1C4
Put a 1 at the front of the function setting to set inverse
output. For example, set 138 for inverse output of 38
[Drive Enabled].
2.8 H: Terminal Functions
Reference
320
320
320
320
320
320
320
320
321
321
321
321
321
321
321
321
321
322
322
322
322
322
322
322
322
322
323
323
323
323
323
323
323
323
324
303
2