YASKAWA HV600 Manual page 55

Setting Value Function
3E PID Setpoint Selection 1
3F PID Setpoint Selection 2
40 Forward RUN (2-Wire)
41 Reverse RUN (2-Wire)
42 Run Command (2-Wire
Sequence 2)
43 FWD/REV (2-Wire
Sequence 2)
44 Add Offset Frequency 1
(d7-01)
45 Add Offset Frequency 2
(d7-01)
46 Add Offset Frequency 3
(d7-01)
50 Motor Pre-heat 2
51 Sequence Timer Disable
YASKAWA TOEPYAIHV6002A HV600 Drive Programming
V/f OLV/PM OLV/PM EZOLV
Sets the function to switch the PID setpoint to YA-02 [Setpoint 2] or YA-04 [Setpoint 4]. Set this function and H1-xx =
3F [PID Setpoint Selection 2] at the same time.
Note:
If you use this function and one of H1-xx = 83 to 85 [Dedicated Multi-Setpoint YA-02 to YA-04] at the same time,
the drive will detect an oPE03 [Multi-Function Input Setting Err].
ON : YA-02 or YA-04 is PID setpoint.
OFF : The frequency reference, YA-01 [Setpoint 1], or YA-03 [Setpoint 3] is PID setpoint.
V/f OLV/PM OLV/PM EZOLV
Sets the function to switch the PID setpoint to YA-03 [Setpoint 3] or YA-04 [Setpoint 4]. Set this function and H1-xx =
3E [PID Setpoint Selection 1] at the same time.
Note:
If you use this function and one of H1-xx = 83 to 85 [Dedicated Multi-Setpoint YA-02 to YA-04] at the same time,
the drive will detect an oPE03 [Multi-Function Input Setting Err].
ON : YA-03 or YA-04 is PID setpoint.
OFF : The frequency reference, YA-01 [Setpoint 1], or YA-02 [Setpoint 2] is PID setpoint.
V/f OLV/PM OLV/PM EZOLV
Sets the Forward Run command for 2-wire sequence 1. Set this function and H1-xx = 41 [Reverse Run Command (2-
Wire Seq)] together.
ON : Forward Run
OFF : Run Stop
Note:
• If you turn ON the Forward Run command terminal and the Reverse Run command terminal, it will cause an EF
[FWD/REV Run Command Input Error] alarm and the motor will ramp to stop.
• Initialize the drive with a 2-wire sequence to set the Forward Run command to terminal S1.
• This function will not operate at the same time as H1-xx = 42, 43 [Run Command/FWD/REV Command (2-Wire
Seq 2)].
V/f OLV/PM OLV/PM EZOLV
Sets the Forward Run command for 2-wire sequence 1. Set this function and H1-xx = 40 [Forward Run Command (2-
Wire Seq)] together.
ON : Reverse Run
OFF : Run Stop
Note:
• If you turn ON the Forward Run command terminal and the Reverse Run command terminal, it will cause an EF
[FWD/REV Run Command Input Error] alarm and the motor will ramp to stop.
• Initialize the drive with a 2-wire sequence to set the Reverse Run command to terminal S2.
• This function will not operate at the same time as H1-xx = 42, 43 [Run Command/FWD/REV Command (2-Wire
Seq 2)].
V/f OLV/PM EZOLV OLV/PM
Sets the Run command for 2-wire sequence 2. Set this function and H1-xx = 43 [FWD/REV Command (2-Wire Seq 2)]
together.
ON : Run
OFF : Stop
Note:
This function will not operate at the same time as H1-xx = 40, 41 [Forward/Reverse Run Command (2-Wire Seq)].
V/f OLV/PM OLV/PM EZOLV
Sets the direction of motor rotation for 2-wire sequence 2. Set this function and H1-xx = 42 [Run Command (2-Wire
Sequence 2)] together.
ON : Reverse run
OFF : Forward run
Note:
This function will not operate at the same time as H1-xx = 40, 41 [Forward/Reverse Run Command (2-Wire Seq)].
V/f OLV/PM EZOLV OLV/PM
Sets the function to add the offset frequency set in d7-01 [Offset Frequency 1] to the frequency reference when the
terminal activates.
V/f OLV/PM EZOLV OLV/PM
Sets the function to add the offset frequency set in d7-02 [Offset Frequency 2] to the frequency reference when the
terminal activates.
V/f OLV/PM EZOLV OLV/PM
Sets the function to add the offset frequency set in d7-03 [Offset Frequency 3] to the frequency reference when the
terminal activates.
V/f OLV/PM EZOLV OLV/PM
Sets the command to apply the motor pre-heat current.
V/f OLV/PM EZOLV OLV/PM
Sets the command to disable Sequence Timers.
ON : Sequence Timer is Disabled
1.10 H: Terminal Functions
Description Ref.
293
293
293
293
294
294
294
294
294
1
295
295
55