Freescale Semiconductor MPC5200B User Manual page 575

PSC Operation Modes
Low-power mode can be left through either a warm or cold reset. The CPU does a warm reset by setting SICR[AWR] for at least 1µs. This
asserts the FRAME frame sync output in AC97 mode. The CPU does a cold reset in two steps:
1. Writes 0 to whichever GPIO is being used as the active low AC97 reset pin for the minimum time specified in the AC97
specification.
2. Writes 0 to PSC1 or PSC2 SICR[ACRB]. CPU should set this bit after writing 1 to the GPIO used for the AC97 reset pin.
Step 2 (above) is required so that the PSC knows when an AC97 cold reset is occurring.
15.3.3.4 Transmitting and Receiving in "Normal" AC97 Mode
When an AC97 Controller is specified (SICR[SIM]=0x3), PSC1 (or PSC2) begins receiving time slot 1 data, 1 bit-clock cycle after the rising
edge of frame sync, regardless of SICR[DTS1] value. However, SICR[SHDIR] must be 0, because the shift order must be msb first. The
PSC divides the bit-clock by 256 to generate a frame sync pulse that is high for 16-bit clock cycles. The transmitter sends 0s until the receiver
detects the Codec-ready condition (1 in the first bit of a new frame).
• Until the receiver detects the Codec ready condition (1 in the first bit of a new frame), no data is put into the Rx FIFO for that frame.
• When a Codec ready condition is detected, the receiver begins loading the Rx FIFO with the received time slot samples and
continues to do so until a 0 is received in the first bit of a new frame.
Figure 15-16 shows a AC97 interface timing diagram example. Because Rx data is sampled on the falling edge of the BitClk, for transmit
purposes, the frame has already started when the receiver detects a Codec-ready condition. For this reason, transmission starts at the next frame
sync after the Codec-ready condition is detected. The PSC stops transmission at the end of the frame in which the first bit of the received
frame is detected low (Codec not ready).
In the "normal" AC97 mode the controller never generate or analyze the Slot0,1 and Slot3 data, expect the Codec-ready bit in Slot0. In
opposite to the enhanced AC97 mode, see
must be in the TxFIFO, for a complete frame must be 13 data words in the TxFIFO. The software must take sure that the data in the control
slots0,1 and 2 match the value in the data slots. For each AC97 slot a 32 bit data word must be in the TxFIFO. The receiver writes 13 32 bit
data words per AC97 frame to the RxFIFO.
Table 15-88 shows an example who to configure the PSC1 in AC97 mode.
Table 15-88. General Configuration Example for "normal" AC97 Mode
Register
CR
SICR 0x03000000
RFALARM
TFALARM
IMR
Port_Config 0x00000030
CR
15.3.3.5 Transmitting and Receiving in "Enhanced" AC97 Mode
To use PSC1 or PSC2 in "Enhanced" AC97 mode the bit SICR[EnAC97] and the SICR[SIM]=0x3 must be selected. The data transmission
is the standard AC97 one, see Section 15.3.3.1, Block Diagram and Signal Definition for AC97
generate the time slot0,1 and 2 data on the transmit site and will analyze received time slot0,1, and 2. Only during "Enhanced" AC97 mode
the registers AC97Slots, AC97CMD
The Rx_Slots field in the AC97Slots
receiver will ignore all data slots from the current frame and will set the SR[UNEX_RX_SLOT] bit. Only the expected and valid tagged data
slots will be in the RxFIFO. This functionality guarantees that the software can assign the data in the RxFIFO to an AC97 slot. Only the order
in the RxFIFO mark the AC97 slot number.
The TX_Slots field in the AC97Slots
generates the related slot0 tag data. If the TxFIFO is empty the transmitter will tag the frame as empty. The transmitter send data if the receiver
detect the "Codec ready state" for the current frame, the Tx FIFO contains the specified data words (defined in the
15-64
Section 15.3.3.5, Transmitting and Receiving in "Enhanced" AC97
Value
0x0A Disable the Tx and Rx part for configuration if the PSC was enabled by the work
before.
Select the AC97 mode
0x0XXX Choose Rx FIFO "almost full" threshold level.
0x0XXX Choose Tx FIFO "almost empty" threshold level.
0xXXXX select the desired interrupt
Select the Pin-Muxing for AC97 mode PSC2, see
0x05 Enable Tx and Rx
and AC97Data are used. In this mode, only the used data slots (3 to 12) are in the FIFOs.
register specify the expected RX data slots. If the received slots doesn't match this specification the
register define, which data slots will be send. All data for these slots must be in TxFIFO. The transmitter
MPC5200B Users Guide, Rev. 1
NOTE
Setting
Mode. But the AC97 controller is able to
Mode.Therefore all data slots
Chapter 2, Signal Descriptions
AC97Slots register) and
Freescale Semiconductor